GOST 21.101-97

UDC 691:002:006.354

INTERSTATE STANDARD

System project documentation for construction

MAIN REQUIREMENTS FOR PROJECT AND WORKING DOCUMENTATION

System of design documents for construction.

MAIN REQUIREMENTS FOR DESIGN AND WORKING DOCUMENTS

OKS 01.100.30

Introduction date 1998-04-01

Foreword

1 DESIGNED State enterprise- Center for Methodology, Rationing and Standardization in Construction (GP CNS) of Gosstroy of Russia

INCLUDED by the Department for the Development of Scientific and Technical Policy and Design and Survey Works of the Gosstroy of Russia

2 ADOPTED by the Interstate Scientific and Technical Commission for Standardization, Technical Regulation and Certification in Construction December 10, 1997

3 INTRODUCED from April 1, 1998 as a state standard Russian Federation Decree of the Gosstroy of Russia dated December 29, 1997 No. 18-75

4 INSTEAD OF GOST 21.101-93

1 area of ​​use

This standard establishes the basic requirements for design and working documentation for the construction of enterprises, buildings and structures for various purposes.

General rules execution of graphic and textual documentation, established in section 5 of this standard, also apply to the reporting technical documentation on engineering surveys for construction.

GOST 2.004-88 ESKD. General requirements to the implementation of design and technological documents on printing and graphic output devices of a computer

GOST 2.101-68 ESKD. Product types

GOST 2.102-68 ESKD. Types and completeness of design documents

GOST 2.105-95 ESKD. General requirements for text documents

GOST 2.108-68 ESKD. Specification

GOST 2.109-73 ESKD. Basic requirements for drawings

GOST 2.113-75 ESKD. Group and basic design documents

GOST 2.114-95 ESKD. Specifications

GOST 2.301-68 ESKD. Formats

GOST 2.302-68 ESKD. Scales

GOST 2.303-68 ESKD. lines

GOST 2.304-81 ESKD. Drawing fonts

GOST 2.305-68 ESKD. Images - views, cuts, sections

GOST 2.306-68 ESKD. Designations of graphic materials and the rules for their application on the drawings

GOST 2.307-68 ESKD. Application of dimensions and limit deviations

GOST 2.308-79 ESKD. Indication on the drawings of the tolerances of shapes and the location of surfaces

GOST 2.309-73 ESKD. Designation of surface roughness

GOST 2.310-68 ESKD. Application on the drawings of designations of coatings, thermal and other types of processing

GOST 2.311-68 ESKD. Thread image

GOST 2.312-72 ESKD. Conditional images and designations of seams of welded joints

GOST 2.313-82 ESKD. Conditional images and designations of one-piece connections

GOST 2.314-68 ESKD. Instructions on the drawings on the marking and branding of products

GOST 2.316-68 ESKD. Rules for drawing inscriptions on drawings, technical requirements and tables

GOST 2.317-69 ESKD. Axonometric projections

GOST 2.410-68 ESKD. Rules for the execution of drawings of metal structures

GOST 2.501-88 ESKD. Accounting and storage rules

GOST 21.110-95 SPDS. Specification of equipment, products and materials

GOST 21.113-88 SPDS. Accuracy designations

GOST 21.114-95 SPDS. Sketch drawing rules general types non-standard products

GOST 21.203-78 SPDS. Rules for accounting and storage of original project documentation

GOST 21.501-93 SPDS. Rules for the implementation of architectural and construction working drawings.

3 General requirements for the composition of documentation

3.1 The composition and content of project documentation for the construction of enterprises, buildings and structures are established by the current building codes and regulations.

3.2 The composition of the working documentation for the construction of a building or structure generally includes:

a) working drawings intended for the production of construction and installation work;

b) working documentation for building products in accordance with GOST 21.501;

c) sketch drawings of general views of non-standard products in accordance with GOST 21.114 *;

d) specifications of equipment, products and materials according to GOST 21.110;

e) other attached documentation provided for by the relevant standards of the Design Documentation System for Construction (SPDS);

e) estimate documentation according to the established forms.

4 General requirements for completing documentation

4.1 Design documentation

4.1.1 Project documentation intended for approval (stage-project, approved part of the working draft) is completed in volumes, as a rule, in separate sections provided for by building codes and regulations. Each volume is numbered with Arabic numerals.

Example - Volume 1 - General Explanatory Note

Volume 2 - Master Plan and Transport

If necessary, the volumes are divided into parts. In this case, the volumes are numbered by type: Volume 1.1, Volume 1.2.

4.1.2 Text and graphic materials included in the volume are completed, as a rule, in the following order:

Cover;

Title page;

The composition of the project;

Explanatory note;

Basic drawings provided by building codes and regulations.

The rules for the design of the cover, title page, content and composition of the project are given in section 9.

4.1.3 Each text and graphic document included in the volume is assigned a designation that indicates title page and in the main inscriptions.

The composition of the designation includes the basic designation, established according to the system in force in the organization, and through a hyphen - the brand and / or code of the project section. Marks of sections of the project are taken by analogy with the marks of the main sets of working drawings given in Appendix A.

Examples

1.2345-PZ Section "General Explanatory Note"

2.2345-GT Section "Master Plan and Transport"

3.2345-12-AC Section "Architectural and construction solutions",

ПЗ - cipher of the project section;

GT and AS - marks of sections of the project.

________________

4.1.4 Text and graphic materials, as a rule, include the volume on sheets folded according to the A4 GOST 2.301 format.

Each volume includes no more than 250 A4 sheets, 150 A3 sheets, 75 A2 sheets and 50 A1 sheets.

4.1.5 General requirements for the implementation of graphic documentation are given in Section 5.

Text documents are performed in accordance with GOST 2.105, taking into account the requirements of section 5 of this standard.

4.2 Working drawings

4.2.1 Working drawings intended for the production of construction and installation works are combined into sets (hereinafter referred to as the main sets) by brand in accordance with Appendix A.

4.2.2 The main set of working drawings of any brand can be divided into several main sets of the same brand (with the addition of a serial number to it) in accordance with the process of organizing construction and installation work.

Example - AC1; AC2; QOL1; QOL2

4.2.3 Each main set of working drawings is assigned a designation, which includes the basic designation established according to the system in force in the organization, and through a hyphen - the brand of the main set.

Example - 2345-12-AP,

where 2345 is the number of the agreement (contract) or the code of the construction object;

12 - number of the building or structure according to the general plan *;

2345-12 - basic designation;

AP - brand of the main set of working drawings.

________________

* For sections of the project related to the construction site as a whole (general explanatory note, master plan and transport, etc.), as well as for working drawings of linear structures, master plan, outdoor communications, this part of the basic designation, as a rule, is excluded.

4.2.4 The main sets of working drawings include general data on working drawings, as well as drawings and diagrams provided for by the SPDS standards.

General data on working drawings

4.2.5 On the first sheets of each main set of working drawings, general data on working drawings are given, including:

a) a list of working drawings of the main set in form 1;

b) a list of reference and attached documents in form 2;

c) a list of the main sets of working drawings in form 2;

d) a list of specifications (if there are several layouts in the main set), performed according to Form 1.

e) symbols not established state standards, and the values ​​of which are not indicated on other sheets of the main set of working drawings;

e) general instructions;

g) other data provided by the relevant SPDS standards.

Forms 1 and 2 with instructions for completing them are given in Appendix B.

4.2.6 The list of working drawings of the main set contains a sequential list of sheets of the main set.

4.2.7 The list of reference and attached documents is compiled by sections:

a) reference documents;

b) attached documents.

In section " Reference Documents" indicate the documents referenced in the working drawings, including:

a) drawings of typical structures, products and assemblies indicating the name and designation of the series and issue number;

b) standards, which include drawings intended for the manufacture of products, indicating their name and designation.

Reference Documents project organization is issued to the customer only under a separate agreement.

In the "Attached documents" section indicate the documents developed in addition to the working drawings of the main set, including:

Working documentation for construction products;

Sketch drawings of general views of non-standard products *;

Specification of equipment, products and materials;

local estimate;

Other documentation provided by the relevant SPDS standards.

The design organization issues the attached documents to the customer simultaneously with the main set of working drawings.

4.2.8 A list of the main sets of working drawings is given on the sheets of general data of the main set of the leading brand **.

If there are several main sets of working drawings of the same brand, a list of sets of this brand is compiled in form 2 of Appendix B, which is given on the general data sheet for each of these sets.

* Perform if necessary.

** The main set of working drawings is appointed by the general designer as the leading brand.

4.2.9 The general instructions give:

a) the basis for the development of working documentation (design assignment, approved project);

b) the mark taken in the working drawings of a building or structure conditionally as zero (as a rule, they are given on architectural and construction drawings);

c) a record of the results of the test for patentability and patent clearance for the first time used or developed in the project technological processes, equipment, devices, structures, materials and products, as well as the numbers of copyright certificates and applications for which decisions were made to issue copyright certificates for the inventions used in the working documentation;

d) a record that the working drawings are developed in accordance with applicable norms, rules and standards;

e) a list of types of work for which it is necessary to draw up certificates of examination of hidden work;

f) information about who owns this intellectual property (if necessary);

g) other necessary instructions.

General instructions should not repeat the technical requirements placed on other sheets of the main set of working drawings, and describe the technical solutions adopted in the working drawings.

5. General rules for the execution of documentation

5.1 When performing design, working and other technical documentation intended for the construction of enterprises, buildings and structures, one should be guided by the requirements of the relevant SPDS standards, as well as standards unified system design documentation(ESKD).

The list of ESKD standards to be taken into account when performing graphic and text documentation for construction is given in Appendix B.

Documentation intended for microfilming must comply with the requirements of the "Reprography" system of standards.

5.2 Drawings are performed at the optimal scale, taking into account their complexity and richness of information.

The scales in the drawings are not indicated, with the exception of product drawings and other cases provided for in the relevant SPDS standards.

5.3 The list of abbreviations of words allowed in the main inscriptions, technical requirements, tables, drawings and specifications, compiled in addition to GOST 2.316 and is given in Appendix D.

Coordination axes

5.4 On the image of each building or structure, the coordination axes are indicated and an independent notation system is assigned to them.

Coordination axes are applied to the images of the building, structures with thin dash-dotted lines with long strokes, denoted by Arabic numerals and capital letters of the Russian alphabet (with the exception of the letters: Ё, 3, Ъ, O, X, C, Ch, Щ, b, Y, b) in circles with a diameter of 6-12 mm.

Omissions in numerical and alphabetic (except for those indicated) designations of the coordination axes are not allowed.

5.5 The numbers indicate the coordination axes along the side of the building and structures with a large number of axes. If there are not enough letters of the alphabet to designate the coordination axes, subsequent axes are designated by two letters.

Example -AA; BB; VV.

5.6 The sequence of numerical and alphabetic designations of the coordination axes is taken according to the plan from left to right and from bottom to top (Figure 1 A) or as shown in pictures 1 b, V.

5.7 The designation of the coordination axes, as a rule, is applied on the left and lower sides of the plan of the building and structure.

If the coordination axes of the opposite sides of the plan do not coincide, the designations of these axes at the divergence points are additionally applied on the upper and / or right sides.

5.8 For individual elements located between the coordination axes of the main load-bearing structures, put additional axes and designate them as a fraction:

above the line indicate the designation of the previous coordination axis;

under the line - additional serial number within the area between adjacent coordination axes in accordance with Figure 1 G.

Picture 1

It is allowed to assign numerical and alphabetic designations to the coordinating axes of half-timbered columns in continuation of the designations of the axes of the main columns without an additional number.

5.9 On the image of a repeating element attached to several coordination axes, the coordination axes are designated in accordance with Figure 2:

« A» - with the number of coordination axes not more than 3;

« b» - » »»» more than 3;

« V» - for all alphabetic and digital coordination axes.

If necessary, the orientation of the coordination axis to which the element is attached, in relation to the neighboring axis, is indicated in accordance with Figure 2 G.

Figure 2

5.10 To designate the coordination axes of block sections of residential buildings, the index "c" is used.

Example - 1s, 2s, Ac, Bs.

On the plans of residential buildings, arranged from block sections, the designations of the extreme coordination axes of the block sections are indicated without an index in accordance with Figure 3.

Figure 3

Application of dimensions, slopes, marks, inscriptions

5.11 The dimension line at its intersection with extension lines, contour lines or center lines is limited by serifs in the form of thick main lines 2-4 mm long, drawn with an inclination to the right at an angle of 45 ° to the dimension line, while the dimension lines should protrude beyond the extreme extension lines by 1-3 mm.

When applying a diameter or radius dimension inside a circle, as well as an angular dimension, the dimension line is limited by arrows. Arrows are also used when dimensioning radii and internal fillets.

5.12 Level marks (heights, depths) of structural elements, equipment, pipelines, air ducts, etc. from the reference level (conditional "zero" mark) are indicated by a conventional sign in accordance with Figure 4 and are indicated in meters with three decimal places separated from an integer comma.

Figure 4

The "zero" mark, taken, as a rule, for the surface of any structural element of a building or structure located near the planning surface of the earth, is indicated without a sign; marks above zero - with a "+" sign; below zero - with a "-" sign.

On views (façades), sections and sections, marks indicate extension lines or contour lines in accordance with Figure 5, on plans - in a rectangle in accordance with Figure 6, except as otherwise specified in the relevant SPDS standards.

5.13 On the plans, the direction of the slope of the planes is indicated by an arrow, above which, if necessary, the slope value is put down as a percentage in accordance with Figure 7 or as a ratio of height and length (for example, 1:7).

It is allowed, if necessary, to indicate the value of the slope in ppm, as a decimal fraction with an accuracy of the third decimal place. In the drawings and diagrams, in front of the dimension number that determines the magnitude of the slope, the sign "Ð" is applied, the acute angle of which should be directed towards the slope.

The designation of the slope is applied directly above the contour line or on the shelf of the leader line.

Figure 5	Figure 6	Figure 7

5.14 Remote inscriptions for multilayer structures should be made in accordance with Figure 8.

5.15 Position numbers (brands of elements) are applied on the shelves of leader lines drawn from the images of the component parts of the object, next to the image without a leader line or within the contours of the depicted parts of the object in accordance with Figure 9.

With a small-scale image, leader lines end without an arrow and a dot.

5.16 The font size for designating the coordination axes and positions (marks) should be one or two numbers larger than the font size adopted for dimensional numbers in the same drawing.

Images (sections, sections, views, fragments)

5.17 Sections of a building or structure are designated by Arabic numerals sequentially within the main set of working drawings.

Independent numbering is allowed only for sections of individual sections of a building, structure or installation, all drawings of which are placed on one sheet or group of sheets, and if these drawings do not contain references to sections located on other sheets of the main set of working drawings.

It is allowed to designate cuts in capital letters of the Russian alphabet.

The direction of view for a section according to the plan of a building and structure is taken, as a rule, from bottom to top and from right to left.

5.18 If separate parts of the view (facade), plan, section require a more detailed image, then additionally carry out remote elements - nodes and fragments.

5.19 When depicting a node, the corresponding place is marked on the view (facade), plan or section with a closed solid thin line (usually a circle or an oval) with the designation on the shelf of the leader line of the serial number of the node in Arabic numeral in accordance with Figure 10.

If the node is placed on another sheet, then the sheet number is indicated under the leader line shelf (Figure 10 A) or on the shelf of the leader line nearby, in brackets, in accordance with Figure 10 b.

If necessary, references to a node placed in another main set of working drawings, or to a typical node, indicate the designation and sheet number of the corresponding main set of working drawings in accordance with Figure 10 V or a series of working drawings of typical units and issue number in accordance with Figure 10 G.

Figure 10

Above the image of the node indicate in the circle its serial number in accordance with Figure 12 A or 12 b.

Figure 11	Figure 12

The node, which is a complete mirror image of another (main) performance, is assigned the same serial number as the main performance, with the addition of the index "n".

5.20 Fragments of plans, sections, facades, as a rule, are marked with a curly bracket in accordance with Figure 13.

Figure 13

Under the curly brace, as well as above the corresponding fragment, the name and serial number of the fragment are applied. If the fragment is placed on another sheet, then they give a link to this sheet.

5.21 Images up to the axis of symmetry of symmetrical plans and facades of buildings and structures, layouts of structural elements, plans for the location of technological, energy, sanitary and other equipment are not allowed.

5.22 If the image (for example, a plan) does not fit on a sheet of the accepted format, then it is divided into several sections, placing them on separate sheets.

In this case, on each sheet where an image section is shown, a diagram of the whole image is given with the necessary coordination axes and a symbol (shading) of the image section shown on this sheet in accordance with Figure 14.

Note - If the drawings of image sections are placed in different main sets of working drawings, then the designation of the corresponding main set is indicated above the sheet number (according to 4.2.2)

Figure 14

5.23 If the floor plans of a multi-storey building have slight differences from each other, then the plan of one of the floors is completely fulfilled, for other floors, only those parts of the plan that are necessary to show the difference from the plan depicted in full are performed.

Under the name of the partially depicted plan, an entry is given:

"For the rest, see the plan (name of the fully depicted plan)."

5.24 In the names of the floor plans of the building and structure indicate the mark of the finished floor or the number of the floor, or the designation of the corresponding cutting plane.

Examples

1. Elevation plan 0.000

2. Plan 2 - 9 floors

3. Plan 3 - 3

When executing a part of the plan, the title indicates the axes that limit this part of the plan.

Example -Elevation plan 0.000 between axes 1 - 8 and A - D

It is allowed to indicate the purpose of the premises located on the floor in the title of the floor plan.

5.25 In the names of the sections of the building (structure) indicate the designation of the corresponding secant plane.

Example -Section 1 - 1

5.26 The names of the facades of buildings and structures indicate the extreme axes between which the facade is located.

Example -Facade 1 - 12

Basic inscriptions

5.27 Each sheet of a graphic and text document must have a main inscription and additional columns to it. The forms of the main inscriptions and instructions for filling them out are given in Appendix D.

5.28 In the design and working documentation, the main inscription is drawn up:

a) on sheets of the main sets of working drawings and main drawings of project documentation - in form 3;

b) on the first sheet of drawings building products- in form 4;

c) on the first sheets of text documents and sketch drawings of general types of non-standard products - in form 5;

d) on subsequent sheets of drawings of building products, text documents and sketch drawings of general views - in form 6.

It is allowed on the first sheet of the drawing of a building product to carry out the main inscription according to form 5.

5.29 In the reporting technical documentation based on the results of engineering surveys, the main inscription is drawn up:

a) on sheets of graphic documents used in the design as a basis - in form 3;

b) on the first sheets of other graphic and text documents - in form 5, on subsequent sheets - in form 6.

5.30 The location of the main inscription and additional columns to it, as well as dimensional frames on the sheets are given in Appendix E.

5.31 The main inscriptions, additional columns to them and frames are made with solid thick main and solid thin lines in accordance with GOST 2.303 in accordance with Appendix D.

5.32 Graphic and text documents, brochured in the form of a volume, album, issue or in other publishing form, are issued with a title page.

Rules for the execution of the title page are given in section 9.

5.33 It is allowed for the title page not to carry out and not to brochure the text working documents of a small volume. In this case, the first sheet of the document is drawn up with the main inscription in form 3, the subsequent ones - in form 6.

6 Rules for making specifications on drawings

6.1 To the layout of elements of a prefabricated structure, a monolithic reinforced concrete structure, to the drawings of installations (blocks) of technological, sanitary and other equipment, a specification is drawn up in form 7 of Appendix G.

When drawing drawings by the group method, group specifications are compiled in form 8 of Appendix G.

6.2 Specifications for building products are made in accordance with GOST 21.501.

7 Rulesmaking changes to the working documentation issued to the customer

7.1 A change in a working document previously issued to the customer is any correction, deletion or addition of any data to it without changing the designation of this document. The designation of the document may be changed only in the case when different documents are erroneously assigned the same designations or an error is made in the designation of the document.

7.2 Changes are made to the original document. Changes to the calculations are not allowed.

7.3 Copies of sheets (modified, additional and issued instead of replaced sheets) of working documentation are sent to organizations to which copies of documents were previously sent, simultaneously with copies of the general data of the corresponding main set of working drawings, specified in accordance with clause 7.5.

7.4

7.4.1 Changing the document is carried out on the basis of permission to make changes (hereinafter referred to as permission), drawn up in accordance with form 9 of Appendix I.

The permission is approved by the head of the organization that developed the document or, on his behalf, another official.

7.4.2 The basis for obtaining original documents for making changes to them is permission.

7.4.3 Changes for each document (for example, the main set of working drawings, specification of equipment, products and materials) are issued with a separate permit.

It is allowed to make one general permission for changes made simultaneously to several documents, if the changes are interconnected or the same for all changed documents.

7.5 Alteration

7.5.1 Changes to the original documents are made by crossing out or erasing (washing out). This takes into account the physical condition of the original.

7.5.2 After making changes, the images, letters, numbers, signs must be clear, the thickness of the lines, the size of the gaps, etc. must be made according to the rules provided for by the relevant ESKD standards and the Reprography standards system.

7.5.3 Changeable sizes, words, signs, inscriptions, etc., are crossed out with solid thin lines and new data is put next to them.

7.5.4 When changing the image (part of the image), it is outlined with a solid thin line forming a closed contour, and crossed out with solid thin lines.

A new image of the changed area is performed on a free field of the sheet or on another sheet without rotation.

7.5.5 Changed, canceled and additional sections of the image are assigned a designation consisting of the serial number of the next change in the document and through the point of the serial number of the changed (cancelled, additional) image section within this sheet. In this case, the new image of the changed area is assigned a change designation of the replaced image.

If a new image of the changed area is placed on another sheet, then the designation of the change assigned to it is saved and is not taken into account in the change table of this sheet.

7.5.6 Near each change, including near the change corrected by erasing (washing), outside the image, the designation of the change is applied in a parallelogram in accordance with Figure 15.

Figure 15

Draw a solid thin line from the parallelogram to the modified area.

7.5.7 Changed sizes, words, signs, inscriptions, etc., located close to each other, are outlined with a solid thin line forming a closed contour, without crossing out in accordance with Figure 16.

7.5.8 If a new image of the changed area is placed on another sheet, then the replaced image also indicates the number of the sheet on which the new image is located in accordance with Figure 17.

Figure 16	Figure 17

7.5.9 Above the new image of the changed area, the designation of the change in the replaced image is placed in the parallelogram, and with the parallelogram it is indicated: "Instead of the crossed out one."

If a new image of the changed area is placed on another sheet, then with a parallelogram indicate: "Instead of the crossed out on the sheet (number of the sheet on which the replaced image is located)" in accordance with Figure 18.

Figure 18

7.5.10 If a new image of the changed area is placed near the replaced one, then they are connected by leader lines with the designation of the change in accordance with Figure 19.

Figure 19

Above the additional image, the designation of the change is placed in the parallelogram, and with the parallelogram they indicate: "Addition" in accordance with Figure 20.

Figure 20

7.5.11 When canceling an image (part of an image), when indicating a change, indicate: "Cancelled".

7.5.12 If there is not enough space to make changes or there may be a violation of the clarity of the image during correction, then a new original is made taking into account the changes made and its previous designation is retained.

If one or more sheets of the original are replaced or added, then the inventory number assigned to the original is stored on them.

When replacing all sheets of the original, it is assigned a new inventory number.

7.5.13 When making changes to the sheets of the main set of working drawings in the list of working drawings of this set on the sheets of general data in the "Note" column indicate:

a) when making the first change - "Change 1".

When making subsequent changes, additionally the next number of changes, separating them from the previous ones with a semicolon.

Example -Change 1; 2; 3

b) on replaced sheets with the change number - "(Replacement)".

Example -Change 1 (Deputy)

c) on canceled sheets with the change number - "Cancelled".

Example -Change 1 (Cancelled)

d) on additional sheets with the change number - "(New)".

Example -Change 1 (New)

7.5.14 If additional sheets are included in the main set of working drawings, then they are assigned successive serial numbers and recorded in continuation of the sheet of working drawings of the corresponding main set.

If there is not enough space in the list of working drawings to record additional sheets, the continuation of the sheet is transferred to the first of the additional sheets. At the same time, at the end of the list of working drawings, placed in the "General Data", an entry is made:

"Continuation of the statement, see sheet (sheet number)", and above the statement on an additional sheet, the heading is placed: "The statement of working drawings of the main set (Continued)".

The numbers and names of the canceled sheets in the list of working drawings are crossed out.

When changing the names of sheets, make the appropriate changes in the column "Name".

7.5.15 When changing the total number of sheets of a document on its first sheet in the main inscription, the corresponding changes are made in the "Sheets" column.

7.5.16 When performing additional and canceling previously completed attached documents, corrections are made to the list of reference and attached documents of the corresponding main set of working drawings.

7.5.17 When performing additional and canceling previously completed main sets of working drawings, corrections are made to the list of main sets of working drawings.

7.5.18 The changes made to the original are indicated in the table of changes placed in the title block.

It is allowed to place the table of changes outside the main inscription (above it or to the left of it) in the same form.

7.5.19 In the table of changes indicate:

a) in the column "Change." - sequence number of the document change;

b) in the column "Number of accounts." - the number of variable areas of the image on this sheet within the next change;

c) in the column "Sheet" - on sheets issued instead of replaced - "Deputy", on sheets added again - "New".

When replacing all sheets of the original (with the next number of changes in the document), on the first sheet in the column "Sheet" indicate "All". At the same time, the table of changes on other sheets of this original is not filled out.

In other cases, a dash is put in the "Sheet" column;

d) in the column "No. Doc." - designation of permission;

e) in the column "Signed." - the signature of the person responsible for the correctness of the change (the signature of the person responsible for normative control is put on the field for filing the sheet);

e) in the column "Date" - the date of the change.

7.5.20 The table of changes does not take into account corrections made to the statements of the general data sheet in connection with changes to the sheets of the main set and attached documents.

7.5.21 When making changes to text documents, it is recommended to follow the change registration table in accordance with Form 10 of Regulation K. The change registration table is placed on the title page of the text document.

7.5.22 Significant changes in text documents are made in one of the following ways:

a) replacement of all or individual sheets of the document;

b) issuance of new additional sheets.

When changing the original text documents, it is allowed, when adding a new sheet, to assign it the number of the previous sheet with the addition of the next Arabic numeral, separating it from the previous dot.

Example - 3.1

In this case, the total number of sheets is changed on the first sheet.

In text documents containing mostly solid text, when adding a new item, it is allowed to assign the number of the previous item to it with the addition of the next lowercase letter of the Russian alphabet, and when canceling the item, keep the numbers of subsequent items.

7.5.23 When canceling or replacing a document, all canceled and replaced sheets of the original are crossed out crosswise with solid thin lines and stamped in the form 11 of Appendix L.

8 Rules for linking working documentation

8.1. Working documentation - standard designs, standard design solutions (intended for binding) and working documentation for re-use are subject to binding to a specific construction site. On each sheet of the attached documentation, a binding stamp is put in accordance with Appendix M:

a) on the first sheet - in form 12;

b) on subsequent sheets - according to form 13.

8.2 Covers and title pages of the main sets of working drawings of standard projects (standard design solutions), published in the form of albums and releases, are not tied and are not sent to the customer.

8.3 Anchor stamp is applied to the free margin of the sheet, preferably above the title block or to the left of it.

8.4 It is allowed not to put a binding stamp on invariable working drawings of structures, products and assemblies if they are re-used by the organization that developed and approved these drawings. The specified working drawings are recorded in the section of the attached documents without changing the designation.

8.5 Changes when binding are made in accordance with paragraphs. 7.5.1-7.5.4, 7.5.14-7.5.17 and subject to the following additional requirements:

a) if there are two or more variable areas of the image, then they are assigned serial numbers, which are put down in Roman numerals on the shelf of the leader line in accordance with Figure 21;

b) above the changed area indicate in Roman numeral the serial number of the changed area of ​​the image and the inscription "Instead of crossed out" in accordance with Figure 22.

If a new image (part of an image) is placed on another sheet, then the number of the sheet on which the new image is located is also indicated for the replaced image.

Figure 21	Figure 22

8.6 The main inscriptions on the sheets of attached documentation published in the form of albums and releases are left unchanged.

8.8 The canceled sheets are excluded from the attached documentation without changing the general numbering of the sheets.

9 Bound Documentation Rules

9.1 Each bound document is issued with a cover in the form 14 given in Appendix H. The cover is not numbered and is not included in the total number of pages.

9.2 The first page of a text (graphic) document or several bound documents is the title page. The title page is performed according to the form 15 of Appendix P. An example of filling out the title page is given in the same place.

9.3 All pages of a bound document, starting with the title one, must have continuous page numbering. The title page is not numbered.

The page number on the sheets of text and graphic documents is indicated in the right upper corner sheet workspace.

In addition, in the main inscription of text and graphic documents included in a volume, album or release and having an independent designation, indicate the serial numbering of sheets within the document with one designation.

9.4 When compiling several documents in the form of a volume, album or release, after the title page, the “Contents” are given, which is performed in the form 2 of Appendix B.

The first sheet of the "Contents" is drawn up with the main inscription in accordance with form 5 of Appendix D, the subsequent ones - in form 6 of Appendix D. The "Contents" are assigned a designation consisting of the designation of the document and the code "C".

Example -2345-GT.S, 2345-11-KZh.IS, 2345-11-TH.NS

9.5 Title pages of design documents are signed by:

manager or chief engineer of the organization;

chief engineer (architect) of the project.

The title pages of working documents are signed responsible person- chief engineer (architect) of the project.

The title page of the reporting survey documentation is drawn up taking into account the additional requirements of the relevant building codes and rules.

9.6 The composition of the project, according to 4.1.2, is given in the statement executed in the form 16 of Appendix P.

The statement provides a sequential list of volumes of project documentation.

The first sheet of the statement is drawn up with the main inscription in form 5 of Appendix D, the subsequent ones - in form 6 of Appendix D.

The statements are assigned a designation consisting of the basic designation of the document and through a hyphen - the code "SP".

Example - 2345-SP

Stamps of the main sets of working drawings

Table A.1

Name of the main set of working drawings		Note
Production technology
Technological communications		When combining working drawings of all technological communications
General plan and transport facilities		When combining the working drawings of the master plan and transport facilities
General plan
Architectural solutions
Interiors		Working drawings can be combined with the main set of grades AP and AC
Reinforced concrete structures
Wooden structures
Architectural and construction solutions		When combining working drawings of architectural solutions and building structures
Detailed metal structures
Water supply and sewerage
Heating, ventilation and air conditioning
Thermal mechanical solutions for boiler rooms
Air supply
dust removal
Refrigeration
Gas supply (internal devices)
Power equipment
Electric lighting (internal)
Communication systems
Radio communications, broadcasting and television
Firefighting
Fire alarm
Security and fire alarm systems
Hydraulic Solutions
Automation…		Many replace the name and brand of the corresponding main set of working drawings
Integrated automation		When combining working drawings of various technological processes and engineering systems
Anticorrosion protection of structures, structures
Anti-corrosion protection of process equipment, gas ducts and pipelines
Thermal insulation of equipment and pipelines
Car roads
Railways
Motor transport facilities		When combining working drawings of roads, railways and other roads
External water supply networks
External sewer networks
External water supply and sewerage networks		When combining working drawings of external water supply and sewerage networks
Thermal mechanical solutions for heating networks
Outdoor gas pipelines
Outdoor electric lighting
Power supply
Note ¾ If necessary, additional brands of the main sets of working drawings can be assigned. At the same time, capital letters (not more than three) of the Russian alphabet are used for stamps, corresponding, as a rule, to the initial letters of the names of the main set of working drawings.

APPENDIX B

(mandatory)

Sheets of general data on working drawings

Form 1 - List of working drawings of the main set

Specification Sheet

Instructions for filling out the list of working drawings of the main set

In the statement of working drawings of the main set indicate:

a) in the column "Sheet" - the serial number of the sheet of the main set of working drawings;

b) in the column "Name" - the name of the images placed on the sheet, in strict accordance with the names given in the main inscription of the sheet;

c) in the column "Note" - additional information, for example, about changes made to the working drawings of the main set.

Instructions for Completing the Specification Sheet

The specification sheet indicates:

a) in the column "Sheet" - the number of the sheet of the main set of working drawings on which the specification is placed;

b) in the column "Name" - the name of the specification in strict accordance with its name indicated on the drawing;

c) in the column "Note" - additional information, including changes made to the specifications.

Form 2 - List of main sets of working drawings

List of referenced and attached documents

Instructions for filling out the list of main sets of working drawings

In the statement of the main sets of working drawings indicate:

a) in the column "Designation" - the designation of the main set of working drawings and, if necessary, the name or distinctive index of the organization that issued the document;

b) in the column "Name" - the name of the main set of working drawings;

c) in the column "Note" - additional information, including changes in the composition of the main sets of working drawings.

Instructions for completing the list of referenced and attached documents

In the statement of reference and attached documents indicate:

a) in the column "Designation" - the designation of the document and, if necessary, the name or distinctive index of the organization that issued the document;

b) in the column "Name" - the name of the document in full accordance with the name indicated on the title page or in the main inscription;

c) in the column "Note" - additional information, including about changes into recorded documents that are part of the working documentation.

APPENDIX B

Mandatory

List of ESKD standards to be taken into account when performing graphic and text documentation for construction

Table B.1

Designation and name of the standard	Conditions for applying the standard
GOST 2.004-88 ESKD. General requirements for the implementation of design and technological documents on printing and graphic output devices of a computer
GOST 2.101-68 ESKD. Product types
GOST 2.102-68 ESKD. Types and completeness of design documents	Taking into account the requirements of GOST 21.501 related to the execution of drawings of building products
GOST 2.105-95 ESKD. General requirements for text documents	Taking into account the requirements of sections 4, 5 and 9 of this standard
GOST 2.108-68 ESKD. Specification	Taking into account the requirements of section 6 of this standard and GOST 21.501
GOST 2.109-73 ESKD. Basic requirements for drawings
GOST 2.113-75 ESKD. Group and basic design documents	Taking into account the requirements of GOST 21.501
GOST 2.114-95 ESKD. Specifications	Subject to the requirements of 5.27, 5.28, 5.30-5.32 of section 5 and section 9 of this standard. 3.7.1 and 3.8 GOST 2.114 do not take into account
GOST 2.301-68 ESKD. Formats	Subject to the requirements of the relevant SPDS standards
GOST 2.302-68 ESKD. Scales
GOST 2.303-68 ESKD. lines
GOST 2.304-81 ESKD. Drawing fonts
GOST 2.305-68 ESKD. Images - views, cuts, sections	Subject to the requirements of 5.17-5.26 of this standard
GOST 2.306-68 ESKD. Designations of graphic materials and the rules for their application on the drawings	Taking into account the requirements of GOST 21.302, tables 4 and 5
GOST 2.307-68 ESKD. Application of dimensions and limit deviations	Taking into account the requirements of 5.11-5.13 of this standard
GOST 2.308-79 ESKD. Indication on the drawings of the tolerances of shapes and the location of surfaces	Taking into account the requirements of GOST 21.113
GOST 2.309-73 ESKD. Surface Roughness Symbols
GOST 2.310-68 ESKD. Application on the drawings of designations of coatings, thermal and other types of processing
GOST 2.311-68 ESKD. Thread image
GOST 2.312-72 ESKD. Conditional images and designations of seams of welded joints
GOST 2.313-82 ESKD. Conditional images and designations of one-piece connections
GOST 2.314-68 ESKD. Instructions on the drawings on the marking and branding of products
GOST 2.315-68 ESKD. Images of simplified and conditional fasteners
GOST 2.316-68 ESKD. Rules for applying inscriptions, technical requirements and tables on drawings	Subject to the requirements of 5.14-5.16 of this standard
GOST 2.317-69 ESKD. Axonometric projections
GOST 2.410-68 ESKD. Rules for the execution of drawings of metal structures
GOST 2.501-88 ESKD. Accounting and storage rules	In terms of the form of the inventory book, subscriber card and instructions for folding drawings
Note - The conditions for the application of ESKD standards of classification group 7 are determined by the corresponding standards of SPDS.

List of allowed word abbreviations (addition to GOST 2.316)

Table D.1

Full name	Reduction
Highway
Anti-seismic seam
Architect
asphalt concrete
Concrete, concrete
ventilation chamber	ventilation chamber
Chief Engineer	Ch. eng. (*)
Chief engineer (architect) of the project	GIP (GAP) (*)
Chief Specialist	Ch. specialist. (*)
Expansion joint
Director
Document
allowed
Unit	Unit rev. (T)
	Capacity (c, t)
Railway
Reinforced concrete, reinforced concrete
manager
insulation, insulating
Institute
Design
Coefficient
Efficiency
Staircase, stairway
Workshop (in design organizations)
materials	materials (t)
Mounting
norms. load
Equipment
checked
calc. load
Sanitary	dignity. tech.
Toilet	dignity. node
Well
Snow
Temperature joint
Technological
Rail head level	ur. r. (And)
Ground level
Clean floor level	ur. ch.p. (i)
Fundamental
Cement, cement
cement concrete
Plaster
Crushed stone, crushed stone
Electric
	e-t (i. t)
Note - Abbreviations marked with (*) are used only in the title block; (t) - in tables; (c) - with numbers or ciphers; (i) - on graphic images

APPENDIX E

(mandatory)

Main inscriptions and additional columns to it

Form 3 - For sheets:

main sets of working drawings;

main drawings of sections of project documentation;

graphic documents on engineering surveys

Form 4 - Dli drawings of building products (first sheet)

Form 5 - Forall types of text documents (first sheets)

Note - The main inscription in form 5 is allowed to be used for graphic documents on engineering surveys that are not used as a background

Form 6 - For drawings of building products and all types of text documents (subsequent sheets)

Note - The main inscription according to form 6 can be used for graphic documents on engineering surveys that are not used as a background

Instructions for filling out the main inscription and additional columns to it

In the columns of the main inscription and additional columns to it (the numbers of the columns are indicated in brackets) lead:

a) in column 1 - the designation of the document, including the project section, the main set of working drawings, product drawing, text document, etc.;

b) in column 2 - the name of the enterprise, housing and civil complex or other construction object, which includes the building (structure), or the name of the microdistrict;

c) in column 3 - the name of the building (structure) and, if necessary, the type of construction (reconstruction, expansion, technical re-equipment, overhaul);

d) in column 4 - the name of the images placed on this sheet, in exact accordance with the name on the drawing.

The names of specifications and other tables, as well as textual indications related to images, are not indicated in the column;

e) in column 5 - the name of the product and / or the name of the document;

e) in column 6 - symbol design stages:

1) P - for project documentation, including the approved part of the working draft;

2) P - for working documentation;

g) in column 7 - the serial number of a sheet or page of a text document for duplex printing. On documents consisting of one sheet, the column is not filled out;

i) in column 8 - total number document sheets. The column is filled out only on the first sheet.

On the first sheet of a text document for duplex printing indicate the total number of pages;

j) in column 9 - the name or distinctive index of the organization that developed the document;

k) in column 10 - the nature of the work performed (developed, checked, standard control).

Depending on the design stage, the complexity and significance of the document, it is allowed to fill in free lines at the discretion of the organization's management (indicate the positions of persons responsible for the development of the document (drawing);

l) in columns 11-13 - the names and signatures of the persons indicated in column 10, and the date of signing.

Signatures of other officials and coordinating signatures are placed on the field for filing the sheet;

m) in columns 14-19 - columns of the table of changes, which are filled in in accordance with clause 7.5.19;

o) in column 20 - the inventory number of the original;

p) in column 21 - the signature of the person who accepted the original for storage, and the date of acceptance (day, month, year);

c) in column 22 - the inventory number of the original document, in exchange for which the original was issued;

r) in column 23 - the designation of the material of the part (the column is filled out only on the drawings of the parts);

s) in column 24 - the mass of the product shown in the drawing, in kilograms, without indicating the unit of measurement. The mass of the product in other units of measurement is given with the indication of the unit of measurement.

Example - 2,4 T;

t) in column 25 - scale (put down in accordance with GOST 2.302);

w) in column 26 - the signature of the person who copied the drawing (if necessary).

APPENDIX E

(mandatory)

Location of the main inscription, additional columns to it

and dimension frames on sheets

Note - Dimensions in parentheses are for the framework of standard design documentation.

APPENDIX G

(mandatory)

Form 7 - WITHspecification

Form 8 - GRpackage specification

Instructions for filling out the specification and group specification

The specifications indicate:

a) in the column "Pos." - positions (brands) of structural elements, installations;

b) in the column "Designation" - the designation of the main documents for the structural elements, equipment and products recorded in the specification or standards (technical specifications) for them;

c) in the column "Name" - the names of structural elements, equipment and products and their brands. It is allowed to indicate the name of a group of elements with the same name once and underline;

d) in the column "Number." forms 7 - the number of elements. In the column “Number ...” of Form 8, instead of the ellipsis, they write “according to the scheme”, “per floor”, etc., and below - the serial numbers of the layout or floors;

e) in the column "Mass, unit kg" - mass in kilograms. It is allowed to give the mass in tons, but with an indication of the unit of measurement;

f) in the column "Note" - additional information, for example, the unit of mass.

APPENDIX AND

(mandatory)

Form 9 - Permission to make changes

Instructions for Completing a Change Authorization

Permissions indicate:

a) in column 1 - the designation of the permit, consisting of the serial number of the permit according to the book of registration of permits in accordance with GOST 21.203 and a dash of the last two digits of the year.

Example - 15-97;

b) in column 2 - the designation of the document in which the change is made;

c) in column 3 - the name of the enterprise under construction, building (structure);

d) in column 4 - the next serial number assigned to the changes that are made to the document by one permit. It is indicated for the entire document, regardless of how many sheets it is made on. The serial numbers of changes are indicated by Arabic numerals;

e) in column 5 - the numbers of the sheets of the document in which changes are made;

f) in column 6 - the content of the change in the form of a text description and / or graphic image;

g) in column 7 - code of the reason for the change in accordance with the table

i) in column 8 - additional information;

j) in columns 9-11 - the names of the persons signing the permit, their signatures and dates of signing;

k) in column 12 - the name of the design organization and the subdivision (department) that issued the permit;

l) in columns 13-16 - the name of the relevant departments or organizations, positions and names of persons with whom in due course agree on the permit, their signatures and dates of signing, as well as the signature of the comptroller;

m) in column 17 - serial number of the permit sheet. If the permit consists of one sheet, the column is not filled out;

o) in column 18 - the total number of permit sheets.

Form 10 - Change Log Table

Instructions for completing the change registration table

In the columns of the change registration table indicate:

a) in the columns "Change", "Document number", "Signed" and "Date" - similar to filling in the corresponding columns of the table of changes;

b) in the columns "Numbers of sheets (pages) changed, replaced, new, canceled" - the numbers of sheets (pages) respectively changed, replaced, added and canceled under this permission.

When replacing the entire document, in the column "Numbers of sheets (pages) replaced" indicate "All";

c) in the column "Total sheets (pages) in the doc." - the number of sheets (pages) in the document. The column is filled in if the columns "Numbers of sheets (pages) new" and / or "Numbers of sheets (pages) canceled" are filled in.

APPENDIX L

(mandatory)

Form 11 - Stamp of cancellation (replacement) of sheets of the original document

Instructions for filling in the cancellation (replacement) stamp of the original document sheets

The stamp indicates:

a) in line 1 - the sequence number of the next change in the document, in accordance with which the sheet was canceled or replaced (for example, "Change 3"). When canceling the sheet, the word "Replaced" in the stamp is crossed out;

b) in columns 2-5 - the position, surname, signature of the person responsible for making changes, and the date of signing.

APPENDIX M

(mandatory)

Form 12 - Anchor stamp (first sheet)

Form 13 - Anchor stamp (subsequent sheets)

Guidelines for completing anchor stamps

When filling in the binding stamps indicate:

a) in column 1 - the new designation of the attached document;

b) in column 2 - the name of the organization that performed the binding;

c) in column 3 - the name of the enterprise under construction, building or structure for which the binding is made;

d) in columns 4-7 - the positions and names of the persons responsible for binding, as well as the person who carried out the normative control, their signatures and dates of signing;

e) in column 8 - the inventory number assigned to the linked document;

f) in column 9 - the number of sheets of the attached document;

g) in columns 10, 11 - the signature of the person who accepted the attached document for storage, and the date of signing.

APPENDIX H

(mandatory)

Form 14 - Cover

Note - The name of the governing body is indicated for state organizations.

APPENDIX P

(mandatory)

Form 15 - Title page

Notes

1 The name of the governing body is indicated for state organizations.

2 The field for signing the document is filled in in accordance with the instructions in section 9.

Title page example

APPENDIX R

(mandatory)

Form 16 - Project composition

Instructions for filling out the sheet

The listing indicates:

In the column "Volume Number" - the number of the volume or its part;

In the column "Designation" - the designation of the document indicated on the title page, and, if necessary, the name or distinctive index of the organization that issued the document;

In the column "Name" - the name of the document in strict accordance with the name indicated on the title page;

In the "Note" column - additional information.

Key words: working documentation, working drawings, general data on working drawings, composition, main sets, specifications, changes, binding, project documentation, graphic and text documents, title page, main inscriptions, signatures.

1 area of ​​use

3 General requirements for the composition of documentation

4 General requirements for completing documentation

4.1 Design documentation

4.2 Working drawings

General data on working drawings

5 General rules for the execution of documentation

Coordination axes

Application of dimensions, slopes, marks, inscriptions

Images (sections, sections, views , fragments)

Basic inscriptions

6 Rules for making specifications on drawings

7 Rules for making changes to the working documentation issued to the customer

7.4 Permission to make changes

7.5 Making changes

8 Rules for linking working documentation

9 Bound Documentation Rules

Annex A Marks of the main sets of working drawings

Annex B Forms 1 and 2 - General Data Sheets for Working Drawings

Annex B List of ESKD standards to be taken into account when performing graphic and text documentation for construction

Appendix D List of allowed word abbreviations (addition to GOST 2.316)

Appendix D Forms 3-6 - Main inscriptions and additional columns to it

Annex E Location of the main inscription, additional columns to it and dimensional frames on sheets

Appendix G Forms 7 and 8 - Specifications

Annex I Form 9 - Permission to make changes

Annex K Form 10 - Change registration table

Annex L Form 11 - Stamp of cancellation (replacement) of sheets of the original document

Appendix M Forms 12 and 13 - Anchor Stamps (First and Subsequent Sheets)

Annex H Form 14 - Cover

Annex P Form 15 - Title page. Title page example

Annex R Form 16 - Project Scope

GOST 21.101-97

INTERSTATE STANDARD

Project documentation system for construction

MAIN REQUIREMENTS FOR PROJECT AND WORKING DOCUMENTATION

Official edition

Interstate Scientific and Technical Commission for Standardization and Technical Regulation and Certification in Construction (MNTKS)

Foreword

1 DEVELOPED by the State Enterprise - the Center for Methodology, Rationing and Standardization in Construction (GP CNS) of the Gosstroy of Russia

INTRODUCED by the Department for the Development of Scientific and Technical Policy and Design and Survey Works of the State Construction of Russia

2 ADOPTED by the Interstate Scientific and Technical Commission for Standardization, Technical Regulation and Certification in Construction (ISTCS) on December 10, 1997

3 ENTERED INTO EFFECT on April 1, 1998 as the state standard of the Russian Federation by the Decree of the State Construction Committee of Russia dated December 29, 1997 No. 18-75

4 INSTEAD OF GOST 21.101-93

From Gosstroy of Russia, State Unitary Enterprise TsPP, 1997

This International Standard may not, in whole or in part, be reproduced, duplicated or distributed as official publication on the territory of the Russian Federation without the permission of the State Construction Committee of Russia

1 area of ​​use............................................... ................................................. ........1

3 General requirements for the composition of the documentation .............................................. .......................3

4 General requirements for completing documentation ............................................................... .......4

5 General rules for the execution of documentation ............................................... ....................10

6 Rules for the implementation of specifications on drawings .............................................. ............18

7 Rules for making changes to the working documentation issued to the customer .......... 19

8 Rules for linking working documentation............................................................... ...................26

9 Bound Documentation Rules............................................................... 27

Annex A Stamps of the main sets of working drawings .......................................... 37

Annex B Forms 1 and 2 - Sheets of general data on working drawings ........ 41

Annex B List of ESKD standards, the requirements of which are subject to

accounting when performing graphic and text documentation

for construction................................................ ............................... 43

Appendix D List of allowed word abbreviations (addition to

GOST 2.316)....................................... ...................................... 46

Appendix E Forms 3,4,5, and 6 - Main inscriptions and additional

graphs to them ............................................... .................................... 49

Annex E Location of the main inscription, additional columns

to it and dimensional frames on sheets .............................................. 54

Annex G Forms 7 and 8- Specifications .................................................. .55

Annex I Form 9 - Permission to make changes .............................. 56

Annex K Form 10 -Change registration table .................................. 59

Annex L Form II - Cancellation (replacement) stamp of the original

document................................. 61

Appendix M Forms 12 and 13 - Anchor Stamps (First and

following sheets) .............................................................. ..........62

Annex H Form 14 - Cover .............................................. ................63

Annex P Form 15 - Cover page .............................................. .....64

Appendix P Title page design example ..................................................65

Annex C Form 16 - Scope of the project .............................................. ......66

INTERSTATE STANDARD

Project documentation system for construction MAIN REQUIREMENTS FOR DESIGN AND WORK

DOCUMENTATION

System of design documents for construction MAIN REQUIREMENTS FOR DESIGN AND WORKING DOCUMENTS

1 AREA OF USE

This standard establishes the basic requirements for design and working documentation for the construction of enterprises, buildings and structures for various purposes.

The general rules for the implementation of graphic and text documentation, established in section 5 of this standard, also apply to reporting technical documentation on engineering surveys for construction.

Official edition

GOST 2.102-68 ESKD. Types and completeness of design documents GOST 2.105-95 ESKD. General requirements for text documents GOST 2.108-68 ESKD. Specification GOST 2.109-73 ESKD. Basic requirements for drawings GOST 2.113-75 ESKD. Group and basic design documents GOST 2.114-95 ESKD. Specifications GOST 2.301-68 ESKD. Formats GOST 2.302-68 ESKD. Scales GOST 2.303-68 ESKD. Lines GOST 2.304-81 ESKD. Drawing fonts GOST 2.305-68 ESKD. Images - views, sections, sections GOST 2.306-68 ESKD. Designations of graphic materials and the rules for their application on the drawings

GOST 2.307-68 ESKD. Application of dimensions and limit deviations GOST 2.308-79 ESKD. Indication on the drawings of the tolerances of shapes and the location of surfaces

GOST 2.309 ESKD. Surface roughness designation GOST 2.310-68 ESKD. Application on the drawings of designations of coatings, thermal and other types of processing

GOST 2.311-68 ESKD. Thread image

GOST 2.312-72 ESKD. Conditional images and designations of seams of welded joints

GOST 2.313-82 ESKD. Conditional images and designations of one-piece connections

GOST 2.314-68 ESKD. Instructions on the drawings on the marking and branding of products

GOST 2.316-68 ESKD. Rules for applying inscriptions, technical requirements and tables on drawings

GOST 2.317-69 ESKD. Axonometric projections

GOST 2.410-68 ESKD. Rules for the execution of drawings of metal structures

GOST 2.501-88 ESKD. Accounting and storage rules

GOST 21.110-95 SPDS. Specification of equipment, products and materials

GOST 21.113-88 SPDS. Accuracy designations

GOST 21.114-95 SPDS. Rules for the implementation of sketch drawings of general views of non-standard products

GOST 21.203-78 SPDS. Rules for accounting and storage of original project documentation

GOST 21.501-93 SPDS. Rules for the implementation of architectural and construction working drawings

3 GENERAL REQUIREMENTS FOR THE COMPOSITION OF DOCUMENTATION

3.1 The composition and content of project documentation for the construction of enterprises, buildings and structures are established by the current building codes and regulations.

3.2 The composition of the working documentation for the construction of a building or structure generally includes:

a) working drawings intended for the production of construction and installation works;

b) working documentation for building products in accordance with GOST 21.501;

c) sketch drawings of general views of non-standard products in accordance with GOST 21.114 *;

d) specifications of equipment, products and materials according to GOST 21.110;

e) other attached documentation provided for by the relevant standards of the Design Documentation System for Construction (SPDS);

f) estimate documentation according to the established forms.

4 GENERAL REQUIREMENTS FOR COMPLETING DOCUMENTATION

4.1 Design documentation

4.1.1 Project documentation intended for approval (project stage, approved part of the working draft) is completed in volumes, as a rule, in separate sections provided for by building codes and regulations. Each volume is numbered with Arabic numerals.

Example - Volume 1 - General Explanatory Note;

Volume 2 - General Plan and Transport.

If necessary, volumes are divided into parts. In this case, the volumes are numbered by type: Volume 1.1; Volume 1.2.

* Perform as needed

4.1.2 The text and graphic materials included in the volume are completed, as a rule, in the following order:

Cover;

Title page;

The composition of the project;

Explanatory note;

Basic drawings provided by building codes and regulations.

Rules for the design of the cover, title page, content and composition of the project

are given in section 9.

4.1.3 Each text and graphic document included in the volume is assigned a designation, which is indicated on the cover, title page and in the main inscriptions. The composition of the designation includes the basic designation, established according to the system in force in the organization, and through a hyphen - the brand and / or code of the project section. Marks of sections of the project are taken by analogy with the marks of the main sets of working drawings given in Appendix A.

2345-PZ Section "General Explanatory Note";

2345-YY Section "Master Plan and Transport";

2345-12-AC Section "Architectural and construction solutions", where:

2345-12 - basic designation;

GT and AS - marks of sections of the project;

ПЗ - cipher of the project section.

4.1.4 Text and graphic materials, as a rule, include the volume on sheets folded according to the A4 GOST 2.301 format.

Each volume includes a maximum of 250 A4 sheets, 150 A3 sheets, 75 A2 sheets, and 50 AI sheets.

4.1.5 General requirements for the implementation of graphic documentation are given in Section 5.

Text documents are performed in accordance with GOST 2.105, taking into account the requirements of section 5 of this standard.

4.2 Working drawings

4.2.1 Working drawings intended for the production of construction and installation works are combined into sets (hereinafter referred to as the main sets) by brand in accordance with Appendix A.

4.2.2 The main set of working drawings of any brand can be divided into several main sets of the same brand (with the addition of a serial number to it) in accordance with the process of organizing construction and installation work.

Example - AC 1; AC2; QOL1; QOL2.

* For sections of the project relating to the construction site as a whole (general explanatory note, master plan and transport, etc.), this part of the basic designation is usually excluded

4.2.3 Each main set of working drawings is assigned a designation, which includes the basic designation established according to the system in force in the organization, and through a hyphen - the brand of the main set.

Example - 2345-12-AP, where:

2345 - the number of the agreement (contract) or the code of the construction object;

12 - number of the building or structure according to the general plan *;

2345-12 - basic designation;

AP - brand of the main set of working drawings.

4.2.4 The main sets of working drawings include general data on working drawings, as well as drawings and diagrams provided for by the relevant SPDS standards.

General data on working drawings

4.2.5 On the first sheets of each main set of working drawings, general data on working drawings are given, including:

a) a list of working drawings of the main set, performed in accordance with form 1;

b) a list of reference and attached documents, performed in accordance with form 2;

c) a list of the main sets of working drawings, performed in accordance with form 2;

d) a list of specifications (if there are several layouts in the main set), performed according to Form 1.

* For working drawings of linear structures, a master plan, external communications, this part of the basic designation is usually excluded

e) symbols that are not established by state standards, and the meanings of which are not indicated on other sheets of the main set of working drawings;

e) general instructions;

g) other data provided by the relevant SPDS standards.

Forms 1 and 2 with instructions for completing them are given in Appendix B.

4.2.6 The list of working drawings of the main set contains a sequential list of sheets of the main set.

4.2.7 The list of reference and attached documents is compiled by sections:

a) reference documents;

b) attached documents.

In the "Referenced Documents" section, indicate the documents that are referenced in the working drawings, including:

a) drawings of typical structures, products and assemblies indicating the name and designation of the series and issue number;

b) standards, which include drawings intended for the manufacture of products, indicating their name and designation.

Reference documents are issued by the design organization to the customer only under a separate agreement.

In the "Attached documents" section indicate the documents developed in addition to the working drawings of the main set, including:

Working documentation for construction products;

Sketch drawings of general views of non-standard products *;

* Perform as needed

Specification of equipment, products and materials;

local estimate;

Other documentation provided by the relevant standards

spds.

The design organization issues the attached documents to the customer simultaneously with the main set of working drawings.

4.2.8 A list of the main sets of working drawings is given on the general data sheets of the main set of the leading brand *.

If there are several main sets of working drawings of the same brand, a list of sets of this brand is compiled in form 2 of Appendix B, which is given on the general data sheet for each of these sets.

4.2.9 The general instructions give:

a) the basis for the development of working documentation (design assignment, approved project);

b) the mark taken in the working drawings of a building or structure conditionally as zero (as a rule, they are given on architectural and construction drawings);

c) a record of the results of the check for patentability and patent purity of technological processes, equipment, devices, structures, products and materials for the first time used or developed in the project, as well as the numbers of copyright certificates and applications for which decisions were made to issue copyright certificates for those used in the working documentation of the invention;

* The main set of working drawings is appointed by the general designer as the leading brand

d) a record that the working drawings are developed in accordance with applicable norms, rules and standards;

e) lists of types of work for which it is necessary to draw up certificates of examination of hidden work;

f) information about who owns this intellectual property (if necessary);

g) other necessary instructions.

General instructions should not repeat the technical requirements placed on other sheets of the main set of working drawings, and describe the technical solutions adopted in the working drawings.

5 GENERAL RULES FOR DOCUMENTATION

5.1 When performing design, working and other technical documentation intended for the construction of enterprises, buildings and structures, one should be guided by the requirements of the relevant SPDS standards, as well as the requirements of the standards of the Unified Design Documentation System (ESKD). The list of ESKD standards, the requirements of which are to be taken into account when performing graphic and text documentation for construction, is given in Appendix B.

Documentation intended for microfilming must comply with the requirements of the "Reprography" system of standards.

5.2 Drawings are performed at the optimal scale, taking into account their complexity and richness of information.

The scales in the drawings are not indicated, with the exception of product drawings and other cases provided for in the relevant SPDS standards.

5.3 The list of abbreviations of words allowed in the main inscriptions, technical requirements, tables, drawings and specifications is compiled in addition to GOST 2.316 and is given in Appendix D.

Coordination axes

5.4 On the image of each building or structure, the coordination axes are indicated and an independent notation system is assigned to them.

The coordination axes are applied to the images of the building, structures with thin dash-dotted lines with long strokes, denoted by Arabic numerals and capital letters of the Russian alphabet (with the exception of the letters: E, 3, Y, O, X, C, Ch, W, b, Y, b) in circles with a diameter of 6-12 mm.

Omissions in numerical and alphabetic (except for those indicated) designations of the coordination axes are not allowed.

5.5 The numbers indicate the coordination axes along the side of the building and structures with a large number of axes. If there are not enough letters of the alphabet to designate the coordination axes, subsequent axes are designated by two letters.

Example - AA; BB; VV.

5.6 The sequence of numerical and alphabetic designations of the coordination axes is taken according to the plan from left to right and from bottom to top (Figure 1 a) or as shown in Figures 1 b, c.

5.7 The designation of the coordination axes, as a rule, is applied on the left and lower sides of the plan of the building and structure. If the coordination axes of the opposite sides of the plan do not coincide, the designations of the indicated axes in the places of divergence are additionally applied on the upper and / or right sides.

5.8 For individual elements located between the coordination axes of the main supporting structures, additional axes are applied and denoted as a fraction: above the line indicate the designation of the previous coordination axis, below the line - an additional serial number within the area between adjacent coordination axes in accordance with Figure 1 d .

It is allowed to assign numerical and alphabetic designations to the coordinating axes of half-timbered columns in continuation of the designations of the axes of the main columns without an additional number.

5.9 On the image of a repeating element linked to several coordination axes, the coordination axes are designated in accordance with Figure 2a (with no more than three coordination axes), with Figure 26 (more than three coordination axes) and with Figure 2c (for all alphabetic and digital coordination axes).

If necessary, the orientation of the coordination axis, to which the element is attached, in relation to the neighboring axis, is indicated in accordance with Figure 2d.

5.10 To designate the coordination axes of block sections of residential buildings, the index "c" is used.

Example - 1s, 2s, As, Bs

On the plans of residential buildings composed of block sections, the designations of the extreme coordination axes of the block sections are indicated without an index in accordance with Figure 3.

Application of dimensions, slopes, marks, inscriptions

5.11 The dimension line at its intersection with extension lines, contour lines or center lines is limited by serifs in the form of thick main

lines 2-4 mm long, drawn with an inclination to the right at an angle of 45 ° to the dimension line, while the dimension lines should protrude and the extreme extension lines by 1 - 3 mm.

When applying a diameter or radius dimension inside a circle, as well as an angular dimension, the dimension line is limited by arrows. Arrows are also used when dimensioning radii and internal fillets.

5.12 Level marks (heights, depths) of structural elements, equipment, pipelines, air ducts, etc. from the reference level (conditional "zero" mark) are indicated by a conventional sign in accordance with Figure 4 and are indicated in meters with three decimal places separated from an integer comma.

The “zero” mark, taken, as a rule, for the surface of any structural element of a building or structure located near the planning surface of the earth, is indicated without a sign; marks above zero - with the sign "+", below zero - with the sign "-".

On views (façades), sections and sections, marks indicate extension lines or contour lines in accordance with Figure 5, on plans - in a rectangle in accordance with Figure 6, except as otherwise specified in the relevant SPDS standards.

5.13 On the plans, the direction of the slope of the planes is indicated by an arrow, above which, if necessary, the slope value is put down as a percentage in accordance with Figure 7 or as a ratio of height and length (for example, 1:7).

It is allowed, if necessary, to indicate the slope value in ppm, as a decimal fraction with an accuracy of up to the third decimal place. On the drawings and diagrams before

the dimension number that determines the magnitude of the slope, put the sign "Z", the acute angle of which should be directed towards the slope. The designation of the slope is applied directly above the contour line or on the shelf of the leader line.

5.14 Remote inscriptions for multilayer structures should be made in accordance with Figure 8.

5.15 Position numbers (marks of elements) are applied on the shelves of leader lines drawn from the images of the component parts of the object, next to the image without a leader line or within the contours of the depicted parts of the object in accordance with Figure 9.

With a small-scale image, leader lines end without an arrow and

5. 16 The font size for designating the coordination axes and positions (marks) should be one or two numbers larger than the font size adopted for dimensional numbers in the same drawing.

Images (sections, sections, views, fragments)

5.17 Sections of a building or structure are designated by Arabic numerals sequentially within the main set of working drawings.

Independent numbering is allowed only for sections of individual sections of a building, structure or installation, all drawings of which are placed on one sheet or group of sheets, and if these drawings do not contain references to sections located on other sheets of the main set of working drawings.

It is allowed to designate cuts in capital letters of the Russian alphabet.

The direction of view for a section according to the plan of a building and structure is taken, as a rule, from bottom to top and from right to left.

5.18 If separate parts of the view (facade), plan, section require a more detailed image, then additionally carry out remote elements - nodes and fragments.

5.19 When depicting a node, the corresponding place is marked on the view (facade), plan or section with a closed solid thin line, as a rule (circle or oval) ^ with the designation on the shelf of the leader line of the serial number of the node in Arabic numeral in accordance with Figure 10.

If the node is placed on another sheet, then the sheet number is indicated under the leader line shelf (Figure 10a) or on the leader line shelf, next to it in brackets, in accordance with Figure 106.

If necessary, references to a node placed in another main set of working drawings, or to a typical node, indicate the designation and sheet number of the corresponding main set of working drawings in accordance with Figure 10c or a series of working drawings of typical assemblies and the issue number in accordance with Figure Yug.

The node, which is a complete mirror image of another (main) performance, is assigned the same serial number as the main performance, with the addition of the index "n".

5.20 Fragments of plans, sections, facades, as a rule, are marked with a curly bracket in accordance with Figure 13.

Under the curly brace, as well as above the corresponding fragment, the name and serial number of the fragment are applied. If the fragment is placed on another

5.21 Images up to the axis of symmetry of symmetrical plans and facades of buildings and structures, layouts of structural elements, plans for the location of technological, energy, sanitary and other equipment are not allowed.

5.22 If the image (for example, a plan) does not fit on a sheet of the accepted format, then it is divided into several sections, placing them on separate sheets.

In this case, on each sheet where an image section is shown, a diagram of the whole image is given with the necessary coordination axes and a symbol (shading) of the image section shown on this sheet in accordance with Figure 14.

5.23 If the floor plans of a multi-storey building have slight differences from each other, then the plan of one of the floors is completely fulfilled, for other floors, only those parts of the plan that are necessary to show the difference from the plan depicted in full are performed.

Under the name of the partially depicted plan, an entry is given:

“For the rest, see the plan (name of the fully depicted plan)”.

5.24 In the names of the floor plans of a building or structure, indicate the mark of the finished floor or the number of the floor, or the designation of the corresponding cutting plane.

1 Plan for elev. 0.000

2 Plan 2-9 floors

3 Plan 3 - 3

When executing a part of the plan, the title indicates the axes that limit this part of the plan.

Example - Plan for elev. 0.000 between axes 1 - 8 and A - D.

It is allowed to indicate the purpose of the premises located on the floor in the title of the floor plan.

5.25 In the names of the sections of the building (structure) indicate the designation of the corresponding secant plane.

Example - Section 1 - 1

5.26 The names of the facades of buildings and structures indicate the extreme axes between which the facade is located.

Example - Front 1-12

Basic inscriptions

5. 27 Each sheet of a graphic and text document must have a main inscription and additional columns to it. The forms of the main inscriptions and instructions for filling them out are given in Appendix D.

5. 28 In the design and working documentation, the main inscription is drawn up:

a) on sheets of the main sets of working drawings and main drawings of project documentation - in form 3;

b) on the first sheet of drawings of building products - in form 4;

c) on the first sheets of text documents and sketch drawings of general views of non-standard products in form 5;

d) on subsequent sheets of drawings of building products, text documents and sketch drawings of general views - in form 6.

It is allowed on the first sheet of the drawing of a building product to carry out the main inscription according to form 5.

5.29 In the reporting technical documentation based on the results of engineering surveys, the main inscription is drawn up:

a) on sheets of graphic documents used in the design as a basis - in form 3;

b) on the first sheets of other graphic and text documents - in form 5, on subsequent sheets - in form 6.

5.30 The location of the main inscription and additional columns to it, as well as dimensional frames on the sheets are given in Appendix E.

5.31 The main inscriptions, additional columns to them and frames are made with solid thick main and solid thin lines in accordance with GOST 2.303 in accordance with Appendix D.

5.32 Graphic and text documents, brochured in the form of a volume, release album or other publishing form, are issued with a title page.

Rules for the execution of the title page are given in section 9.

5.33 It is allowed for the title page not to carry out and not to brochure the text working documents of a small volume. In this case, the first sheet of the document is drawn up with the main inscription in form 3, the subsequent ones - in form 6.

6 RULES FOR IMPLEMENTATION OF SPECIFICATIONS ON DRAWINGS

6.1 To the layout of the elements of the prefabricated structure, monolithic reinforced concrete structure, to the drawings of installations (blocks) of the technological,

sanitary and other equipment make up a specification in form 7 of Appendix G.

When drawing drawings by the group method, group specifications are compiled in form 8 of Appendix G.

6.2 Specifications for building products are made in accordance with GOST 21.501.

7 RULES FOR AMENDING THE WORKING DOCUMENTATION,

ISSUED TO THE CUSTOMER

7.1 A change in a working document previously issued to the customer is understood as any correction, deletion or addition of any data to it without changing the designation of this document. The designation of the document may be changed only in the case when different documents are erroneously assigned the same designations or an error is made in the designation of the document.

7.2 Changes are made to the original document. Changes to the calculations are not allowed.

7.3 Copies of the amended, additional and issued instead of replaced sheets of working documentation are sent to organizations to which copies of documents were previously sent, together with copies of the general data of the corresponding main set of working drawings, refined in accordance with 7.5.

7.4 Permission to make changes

7.4.1 Changing the document is carried out on the basis of permission to make changes (hereinafter referred to as permission), drawn up in accordance with form 9 of Appendix I.

The permission is approved by the head of the organization that developed the document or, on his behalf, another official.

7.4.2 The basis for obtaining original documents for making changes to them is permission.

7.4.3 Changes for each document (for example, the main set of working drawings, specification of equipment, products and materials) are issued with a separate permit.

It is allowed to make one general permission for changes made simultaneously to several documents, if the changes are interconnected or the same for all changed documents.

7.5 Making changes

7.5.1 Amendments to the original documents are made by crossing out or erasing (washing out). This takes into account the physical condition of the original.

7.5.2 After making changes, the images, letters, numbers, signs must be clear, the thickness of the lines, the size of the gaps, etc. must be performed according to the rules provided for by the relevant standards of the ESKD and the "Reprography" system of standards.

7.5.3 Changeable sizes, words, signs, inscriptions, etc. cross out with solid thin lines and next put down new data.

7.5.4 When changing the image (part of the image), it is outlined with a solid thin line forming a closed contour, and crossed out with solid thin lines. A new image of the changed area is performed on a free field of the sheet or on another sheet without rotation.

7.5.5 Changed, canceled and additional sections of the image are assigned a designation consisting of the serial number of the next change in the document and through the point of the serial number of the changed (cancelled, additional) image section within this sheet. In this case, the new image of the changed area is assigned a change designation of the replaced image.

If a new image of the changed area is placed on another sheet, then the designation of the change assigned to it is saved and is not taken into account in the change table of this sheet.

7.5.6 Near each change, including near the change corrected by erasing (washing), outside the image, the designation of the change is applied in a parallelogram in accordance with Figure 15.

Draw a solid thin line from the parallelogram to the modified area.

7.5.7 Closely spaced altered sizes, words, signs, inscriptions, etc. encircle with a solid thin line forming a closed contour, without crossing out in accordance with Figure 16.

7.5.8 If a new image of the changed area is placed on another sheet, then the replaced image also indicates the number of the sheet on which the new image is located in accordance with Figure 17.

7.5.9 Above the new image of the changed area, the designation of the change in the replaced image is placed in the parallelogram, and with the parallelogram they indicate: “Instead of the crossed out“.

If a new image of the changed area is placed on another sheet, then with a parallelogram they indicate: “Instead of the one crossed out on the sheet (sheet number, on

which the replaced image is located)” in accordance with Figure 18.

7.5.10 If a new image of the changed area is placed near the replaced one, then they are connected by leader lines with the designation of the change in accordance with Figure 19.

Above the additional image, the designation of the change is placed in the parallelogram, and with the parallelogram they indicate: “Addition” in accordance with Figure 20.

7.5.11 When canceling an image (part of an image), when indicating a change, indicate: "Cancelled".

7.5.12 If there is not enough space to make changes or there may be a violation of the clarity of the image during correction, then a new original is made taking into account the changes made and its previous designation is retained.

If one or more sheets of the original are replaced or added, then the inventory number assigned to the original is stored on them.

When replacing all sheets of the original, it is assigned a new inventory

7.5.13 When making changes to the sheets of the main set of working drawings in the list of working drawings of this set on the sheets of general data in the column

"Note" indicate:

a) when making the first change - "Change 1".

When making subsequent changes, additionally the next number of changes, separating them from the previous ones with a semicolon.

Example - Change. G, 2; 3

b) on replaced sheets with a change number - "(Replacement)".

Example - Change. 1 (Deputy)

c) on canceled sheets with the change number - "Cancelled".

Example - Change. 1 (Cancelled)

d) on additional sheets with the change number - "(New)"

Example - Change. 1 (New)

7.5.14 If additional sheets are included in the main set of working drawings, then they are assigned successive serial numbers and recorded in continuation of the sheet of working drawings of the corresponding main set.

If there is not enough space in the list of working drawings, to record additional sheets, the continuation of the sheet is transferred to the first of the additional sheets. At the same time, at the end of the list of working drawings, placed in the "General Data", an entry is made:

"Continuation of the statement, see sheet (sheet number)", and above the statement on an additional sheet, the heading is placed: "The statement of working drawings of the main set (Continued)".

The numbers and names of the canceled sheets in the list of working drawings are crossed out.

When changing the names of sheets, make the appropriate changes in the column "Name".

7.5.15 When changing the total number of sheets of a document on its first sheet in the main inscription, the corresponding changes are made in the "Sheets" column.

7.5.16 When performing additional and canceling previously completed

attached documents make corrections to the list of reference and attached documents of the corresponding main set of working drawings.

7.5.17 When performing additional and canceling previously completed main sets of working drawings, corrections are made to the list of main sets of working drawings.

7.5.18 The changes made to the original are indicated in the table of changes placed in the title block.

It is allowed to place the table of changes outside the main inscription (above it or to the left of it) in the same form.

7.5.19 In the table of changes indicate:

a) in the column "Change." - sequence number of the document change;

b) in the column "Number of accounts." - the number of variable areas of the image on this sheet within the next change;

c) in the column "Sheet" - on sheets, issued instead of replaced ones, - "Deputy", on sheets added again - "New".

When replacing all sheets of the original (with the next serial number of the document change), on the first sheet in the column "Sheet" indicate "All". At the same time, the table of changes on other sheets of this original is not filled out.

In other cases, a dash is put in the "Sheet" column;

d) in the column "No. Doc." - designation of permission;

e) in the column "Signed." - the signature of the person responsible for the correctness of the change (the signature of the person responsible for normative control is put on the field for filing the sheet);

e) in the column "Date" - the date of the change.

7.5.20 The table of changes does not take into account corrections made to the statements of the general data sheet in connection with changes to the sheets of the main set and attached documents.

7.5.21 When making changes to text documents, it is recommended to follow the change registration table in the form 10 of Appendix K. The change registration table is placed on the title page of the text document.

7.5.22 Significant changes in text documents are made in one of the following ways:

a) replacement of all or individual sheets of the document;

b) by issuing new additional sheets.

When changing the original text documents, it is allowed, when adding a new sheet, to assign it the number of the previous sheet with the addition of the next Arabic numeral, separating it from the previous dot.

Example - 3.1

In this case, the total number of sheets is changed on the first sheet.

In text documents containing mostly solid text, when adding a new item, it is allowed to assign the number of the previous item to it with the addition of the next lowercase letter of the Russian alphabet, and when canceling the item, keep the numbers of subsequent items.

7.5.23 When canceling or replacing a document, all canceled and replaced sheets of the original are crossed out crosswise with solid thin lines and stamped in the form 11 of Appendix L.

8 RULES FOR LINKING WORKING DOCUMENTATION

8.1 Working documentation - standard designs, standard design solutions (intended for binding) and working documentation for reuse are to be linked to a specific construction site. On each sheet of the attached documentation, a binding stamp is put in accordance with Appendix M.

a) on the first sheet - in form 12;

b) on subsequent sheets - according to form 13.

8.2 Covers and title pages of the main sets of working drawings of standard projects (standard design solutions), printed in the form of albums and issues, are not tied and are not sent to the customer.

8.3 Anchor stamp is applied to the free margin of the sheet, preferably above the title block or to the left of it.

8.4 It is allowed not to put a binding stamp on invariable working drawings of structures, products and assemblies if they are re-used by the organization that developed and approved these drawings. The specified working drawings are recorded in the section of the attached documents without changing the designation.

8.5 Changes during binding are made in accordance with 7.5.1 - 7.5.4, 7.5.14 - 7.5.17 and taking into account the following additional requirements:

a) if there are two or more variable areas of the image, then they are assigned serial numbers, which are put down in Roman numerals on the shelf of the leader line in accordance with Figure 21;

b) above the modified area indicate the serial number in Roman numeral

of the image area to be changed and the inscription "Instead of crossed out" in accordance with Figure 22.

If a new image (part of an image) is placed on another sheet, then the number of the sheet on which the new image is located is also indicated for the replaced image.

8.6 The main inscriptions on the sheets of attached documentation published in the form of albums and releases are left unchanged.

8.8 The canceled sheets are excluded from the attached documentation without changing the general numbering of the sheets.

9 RULES FOR REGISTRATION OF BINDING DOCUMENTATION

9.1 Each bound document is issued with a cover in the form 14 given in Appendix H. The cover is not numbered and is not included in the total number of pages.

9.2 The first page of a text (graphic) document or several bound documents is the title page. The title page is performed in accordance with form 15 of Appendix P. An example of filling out the title page is given in Appendix P.

9.3 All pages of a bound document, starting with the title one, must have continuous page numbering. The title page is not numbered.

The page number on sheets of text and graphic documents is indicated in the upper right corner of the working field of the sheet.

In addition, in the main inscription of text and graphic documents included in a volume, album or release and having an independent designation, indicate the serial numbering of sheets within the document with one designation.

9.4 When compiling several documents in the form of a volume, album or release, after the title page, the "Contents" are given, which is performed according to form 2.

The first sheet of the Contents is drawn up with the main inscription according to form 5, the subsequent ones - according to form 6. The content is assigned a designation consisting of the document designation and the cipher "C".

Example - 2345-GT.S; 2345-11-KZh.IS; 2345-11-TX.NS

9.5 Title pages of design documents are signed by:

a) the head or chief engineer of the organization;

b) chief engineer (architect) of the project.

The title pages of working documents are signed by the responsible person - the chief engineer (architect) of the project.

The title page of the reporting survey documentation is drawn up taking into account the additional requirements of the relevant building codes and regulations.

9.6 The composition of the project, according to 4.1.2, is given in the statement executed in the form 16 of Appendix C.

The statement provides a sequential list of volumes of project documentation.

The first sheet of the statement is drawn up with the main inscription in form 5, the subsequent ones - in form 6.

The statements are assigned a designation consisting of the basic designation of the document and through a hyphen - the code "SP".

Example - 2345 - SP

Figure 2

Figure 4

4,500y~ + 2,700^

0,000

Figure 5

Note - The numbers conventionally indicate the sequence

POSITIONS OF THE STRUCTURAL LAYERS AND MARKINGS ON THE SHELVES OF THE LEADER LINE Figure 8

Figure 9

5

zz

Figure 11

2

Figure 10

Node number tagged

on this sheet

Node number

A

The sheet on which the node is labeled

Figure 12

Note - If the plot drawings are placed in different main sets of working drawings, then the designation of the corresponding main set is indicated above the sheet number

2

Figure 19

Addition

XSee fox/n 9

Figure 21

I Instead of what was crossed out on sheet 8

Stamps of the main sets of working drawings

Table A.1

Production technology
T echnological communications		When combining working drawings of all technological communications
General plan and transport facilities		When combining the working drawings of the master plan and transport facilities
General plan
Architectural solutions
Interiors		Working drawings can be combined with the main set of brand AP or AC
Constructions reinforced concrete
Wooden structures
Architectural and construction solutions		When combining working drawings of architectural solutions and building structures
Constructions metal detailing
Water supply and sewerage
Heating, ventilation and

conditioning

		Note
Thermal mechanical solutions for boiler rooms
Air supply
dust removal
Refrigeration
Gas supply (indoor devices)
electrical equipment
Electric lighting (internal)
Communication systems
Radio communications, broadcasting and television
Firefighting
Fire alarm
Security and fire alarm systems
Hydraulic Solutions

Continuation of table A. 1

Name of the main set of working drawings		Note
Automation...		The ellipsis is replaced by the name and brand of the corresponding main set of working drawings
Integrated automation		When combining working drawings of various technological processes and engineering systems
Anticorrosive protection of structures of buildings, structures
Anti-corrosion protection of process equipment, gas ducts and pipelines
Thermal insulation of equipment and pipelines
Car roads
Railways
Transport facilities		When combining working drawings of automobile, railway and other roads
External water supply networks
Outdoor networks

sewers

Name of the main set of working drawings		Note
External water supply and sewerage networks		When combining working drawings of external water supply and sewerage networks
Thermal mechanical solutions for heating networks
Outdoor gas pipelines
outdoor electric lighting
Power supply
Note - If necessary, additional brands of the main sets of working drawings can be assigned. At the same time, capital letters (no more than three) of the Russian alphabet are used for stamps, corresponding, as a rule, to the initial letters of the name of the main set of working drawings.

STATEMENTS OF GENERAL DATA FOR WORKING DRAWINGS

Form 1 List of working drawings of the main set List of specifications

			Name	Note

Instructions for filling out the sheet of working drawings

main set

In the statement of working drawings of the main set indicate:

a) in the column "Sheet" - the serial number of the sheet of the main set of working drawings;

b) in the column "Name" - the name of the images placed on the sheet, in strict accordance with the names given in the main inscription of the sheet;

c) in the column "Note" - additional information, for example, about changes made to the working drawings of the main set.

Instructions for Completing the Specification Sheet

The specification sheet indicates:

a) in the column "Sheet" - the number of the sheet of the main set of working drawings on which the specification is placed;

b) in the column "Name" - the name of the specification in strict accordance with its name indicated on the drawing;

c) in the column "Note" - additional information, incl. about the changes

included in the specifications.

Form 2 List of main sets of working drawings List of reference and attached documents

		Designation	Name	Note

Instructions for filling out the statement of the main sets of working drawings The statement of the main sets of working drawings indicates:

a) in the column "Designation" - the designation of the main set of working drawings and, if necessary, the name or distinctive index of the organization that issued the document;

b) in the column "Name" - the name of the main set of working drawings;

c) in the column "Note" - additional information, incl. on changes in the composition of the main sets of working drawings.

Instructions for filling out the list of reference and attached documents The list of reference and attached documents indicates:

a) in the column "Designation" - the designation of the document and, if necessary, the name or distinctive index of the organization that issued the document;

b) in the column "Name" - the name of the document in strict accordance with the name indicated on the title page or in the main inscription;

c) in the column "Note" - additional information, incl. on the changes made to the recorded documents included in the working documentation.

List of ESKD standards, the requirements of which are to be taken into account when performing graphic and text documentation for construction

BT table
	Conditions for applying the standard
GOST 2.004-88 ESKD. General requirements for the implementation of design and technological documents on printing and graphic output devices of a computer GOST 2.101-68 ESKD. Product types GOST 2.102-68 ESKD. Types and completeness of design documents	Taking into account the requirements of GOST 21.501 related to the execution of drawings, building products
GOST 2.105-95 ESKD. General requirements for text documents	Subject to the requirements of sections 4.5 and 9 of this standard
GOST 2.108-68 ESKD. Specification	Taking into account the requirements of section 6 of this standard and GOST 21.501
GOST 2.109-73 ESKD. Basic requirements for drawings
GOST 2.113-75 ESKD. Group and basic design documents	Taking into account the requirements of GOST 21.501
GOST 2.114-95 ESKD. Specifications	Subject to the requirements of 5.27, 5.28, 5.30-5.32 section 5 and section 9 of this standard. 3.7.1 and 3.8 do not take into account

Table B. 1 continued
Designation and name of the standard	Conditions for applying the standard
GOST 2.301-68 ESKD. Formats	Subject to the requirements of the relevant SPDS standards
GOST 2.302-68 ESKD. Scales
GOST 2.303-68 ESKD. lines
GOST 2.304-81 ESKD. Drawing fonts
GOST 2.305-68 ESKD. Images - views, cuts, sections	Subject to the requirements of 5.17 -5.26 of this standard
GOST 2.306-68 ESKD. Designations of graphic materials and the rules for their application on the drawings	Taking into account the requirements of GOST 21.302, tables 4 and 5
GOST 2.307-68 ESKD. Application of dimensions and limit deviations	Subject to the requirements of 5.11, 5.12, 5.13 of this standard
GOST 2. 308-79 ESKD. Indication on the drawings of the tolerances of shapes and the location of surfaces GOST 2.309-73 ESKD. Surface Roughness Symbols GOST 2.310-68 ESKD. Application on the drawings of designations of coatings, thermal and other types of processing	Taking into account the requirements of GOST 21.113

End of table B.1

Designation and name of the standard	Conditions for applying the standard
GOST 2.311-68 ESKD. Thread image
GOST 2.312-72 ESKD. Conditional images and designations of seams of welded joints
GOST 2.313-82 ESKD. Conditional images and designations of one-piece connections
GOST 2.314-68 ESKD. Instructions on the drawings on the marking and branding of products
GOST 2.315-68 ESKD. Images of simplified and conditional fasteners
GOST 2.316-68 ESKD. Rules for applying inscriptions, technical requirements and tables on drawings	Subject to the requirements of 5.14-5.16 of this standard
GOST 2.317-69 ESKD. Axonometric projections
GOST 2.410-68 ESKD. Rules for the execution of drawings of metal structures
GOST 2.501-88 ESKD. Accounting and storage rules	In terms of the form of the inventory book, subscriber card and instructions for folding drawings
Note - The conditions for the application of ESKD standards of classification group 7 are determined by the corresponding standards of SPDS.

List of allowed word abbreviations (addition to GOST 2.316) Table D.1

Full name	Reduction
Highway
Anti-seismic seam
Architect
asphalt concrete
Concrete, concrete
ventilation chamber	ventilation chamber
Chief Engineer	Ch. eng. (*)
Chief engineer (architect) of the project	GIP (GAP) (*)
Chief Specialist	Ch. specialist. (*)
Expansion joint
Director
Document
allowed
Unit	Unit meas (t)
	Capacity (c, t)
Railway

Continuation of table D. 1
Full name	Reduction
Reinforced concrete, reinforced concrete
manager
insulation, insulating
Institute
Design
Coefficient
Efficiency
Staircase, stairway
Workshop (in design organizations)
materials	materials (t)
Mounting
norms. load
Equipment
checked
calc. load
Sanitary	dignity. tech.
Toilet
Well

End of table D.1

Full name	Reduction
Snow
Temperature joint
Technological
Rail head level	ur. b.b. (And)
Ground level
Clean floor level	ur. ch.p. (i)
Fundamental
Cement, cement
cement concrete
Plaster
Crushed stone, crushed stone
Electric
	e-t (i. t)

Note - Abbreviations marked with (*) are used only in the title block; sign (t) - in tables, sign (c) - with numbers or ciphers; sign (s)-on graphic images.

BASIC INscriptions

Form 3 - Main inscription and additional columns to it for sheets: main sets of working drawings, main drawings of sections of project documentation, graphic documents on engineering surveys

Form 4 - Main inscription and additional columns to it for drawings of building products (first sheet)

Form 5 - Main inscription and additional columns to it for all types of text documents (first sheets)

(V

Hopiroyl (Zb?

Note - The main inscription in form 5 can be used for graphic documents on engineering surveys that are not used as a base

Form 6 - Main inscription and additional columns to it for drawings of building products and all types of text documents (subsequent sheets)

l-

%

copyo^a/r (2£>T

Note - The main inscription in form 6 can be used for graphic documents on engineering surveys that are not used as a base

Instructions for filling in the main inscription and additional columns to it In the columns of the main inscription and additional columns to it (numbers of the columns

indicated in parentheses) give:

a) in column 1 - the designation of the document, incl. project section, main set of working drawings, product drawing, text document, etc.;

b) in column 2 - the name of the enterprise, housing and civil complex or other construction object, which includes the building (structure), or the name of the microdistrict;

c) in column 3 - the name of the building (structure) and, if necessary, the type of construction (reconstruction, expansion, technical re-equipment, overhaul);

d) in column 4 - the name of the images placed on this sheet, in exact accordance with their name on the drawing. The names of specifications and other tables, as well as textual indications related to images, are not indicated in the column;

e) in column 5 - the name of the product and / or the name of the document;

f) in column 6 - designation of the design stage:

1) P - for project documentation, incl. the approved part of the working draft;

2) P - for working documentation;

g) in column 7 - the serial number of a sheet or page of a text document for double-sided printing. On documents consisting of one sheet, the column is not filled out;

i) in column 8 - the total number of sheets of the document.

The column is filled out only on the first sheet. On the first sheet of a text document for duplex printing indicate the total number of pages;

j) in column 9 - the name or distinctive index of the organization that developed the document;

k) in column 10 - the nature of the work performed (developed, checked, standard control). Depending on the design stage, the complexity and significance of the document, it is allowed to fill in free lines at the discretion of the organization's management with the positions of persons responsible for the development of the document (drawing);

l) in columns 11-13 - the names and signatures of the persons indicated in column 10, and the date of signing.

Signatures of other officials and coordinating signatures are placed on the field for filing the sheet,

m) in columns 14-19 - columns of the table of changes, which are filled in in accordance with 7.5.19;

o) in column 20 - the inventory number of the original;

p) in column 21 - the signature of the person who accepted the original for storage, and the date of acceptance (day, month, year);

c) in column 22 - the inventory number of the original document, in exchange for which the original was issued;

r) in column 23 - the designation of the material of the part (the column is filled out only on the drawings of the parts);

s) in column 24 - the mass of the product shown in the drawing in kilograms without indicating the unit of measurement. The mass of the product in other units of measurement is given with the indication of the unit of measurement.

Example - 2.4 tons;

t) in column 25 - scale (put down in accordance with GOST 2.302);

w) in column 26 - the signature of the person who copied the drawing (if necessary).

Location of the main inscription, additional columns to it and dimensional

frames on sheets

Note - Dimensions in brackets are indicated for the scope of standard documentation

	O5ozy<у1/е/уие	ttaunieHoOo/jise.

Form 8 - Group specification

0£oznsg

f/ameooba/i/e

Instructions for completing the specification and

group specification

The specifications indicate:

a) in the column "Pos." - positions (brands) of structural elements, installations;

b) in the column "Designation" - the designation of the main documents for the structural elements, equipment and products recorded in the specification or standards (technical specifications) for them;

c) in the column "Name" - the names of structural elements, equipment, products and their brands. It is allowed to indicate the name of a group of elements with the same name once and underline it.

d) in the column “Number” of the form 7 - the number of elements. In the column “Number ...,” columns 8 - instead of the ellipsis, they write “according to the scheme”, “per floor”, etc., and the lower serial numbers of the layout or floors;

e) in the column ''Mass, units. kg” is the mass in kilograms. It is allowed to give the mass in tons, but with an indication of the unit of measurement;

f) in the column "Note" - additional information, for example, a unit of mass.

Form 9 - Permission to make changes

Instructions for completing the Application Permit

changes

Permissions indicate:

a) in column 1 - the designation of the permit, consisting of the serial number of the permit according to the book of registration of permits in accordance with GOST 21.203 and a dash of the last two digits of the year.

Example -15-97;

b) in column 2 - the designation of the document in which the change is made;

c) in column 3 - the name of the enterprise under construction, building (structure);

d) in column 4 - the next serial number assigned to the changes that are made to the document by one permit. It is indicated for the entire document, regardless of how many sheets it is made on. The serial numbers of changes are indicated by Arabic numerals;

e) in column 5 - the numbers of the sheets of the document in which changes are made;

f) in column 6 - the content of the change in the form of a text description and / or graphic image;

g) in column 7 - code of the reason for the change in accordance with Table 1.

Table 1

i) in column 8 - additional information;

j) in columns 9-11 - the names of the persons signing the permit, their signatures and the date of signing;

k) in column 12 - the name of the design organization and the subdivision (department) that issued the permit;

l) in columns 13-16 - the name of the relevant departments or organizations, the position or nature of the work performed and the names of the persons with whom the permit is agreed in the prescribed manner, their signatures and dates of signing, as well as the signature of the normative controller;

m) in column 17 - serial number of the permit sheet. If the permit consists of one sheet, the column is not filled out;

o) in column 18 - the total number of permit sheets.

Iex- NERVOUS

Total sheets, (pages) per PKD. .

Sheet (page) numbers

Change registration table

Instructions for completing the registration table

changes

In the columns of the change registration table indicate:

a) in the columns “Change. “Document number.”, “Sub.” and “Date” - similar to filling in the corresponding columns of the table of changes;

b) in the columns “Numbers of sheets (pages) changed, replaced, new, canceled” - the numbers of sheets (pages) respectively changed, replaced, added and canceled under this permission.

When replacing the entire document, in the column “Numbers of sheets (pages) replaced” indicate “All”;

c) in the column “Total sheets (pages) in the doc. ” - the number of sheets (pages) in the document. The column is filled in if the columns “Numbers of sheets (pages) new” and / or numbers of sheets (pages) canceled are filled in.

		CANCELLED “REPLACED (1] -RESOLUTION N*?.... FROM.....

Instructions for filling in the cancellation (replacement) stamp of the original document The stamp indicates:

a) in line 1 - the serial number of the next change in the document, in accordance with which the sheet was canceled or replaced (for example, "Change 3"). When canceling the sheet, the word "Replaced" in the stamp is crossed out;

b) in columns 2-5 - position, surname, signature, person responsible for

changes, and the date of signing.

Form 12 - Anchor Stamps (first sheet)

a) in column 1 - the new designation of the attached document;

b) in column 2 - the name of the organization that performed the binding;

c) in column 3 - the name of the enterprise under construction, building or structure for which the binding is made;

d) in column 4-7, the positions and names of the persons responsible for the binding, as well as the person who carried out the normative control, their signatures and dates of signing;

e) in column 8 - the inventory number assigned to the linked document;

f) in column 9 - the number of sheets of the attached document;

g) in columns 10,11 - the signature of the person who accepted the attached document for storage, and the date of signing.

Form 14 - Cover

Name of the governing body whose system includes

organization

Name of the enterprise, building (structure)

Title of the document

Document designation

Volume number

The year of publishing

Note - The name of the governing body is indicated by state organizations

Name of the governing body in whose system the organization belongs

Name of the organization that compiled the document

Name of the enterprise, building ^ construction)

Title of the document

Document designation Volume number

Signature positions

The year of publishing

Notes

1 The name of the governing body is indicated for state organizations

2 The field for signing the document is filled in in accordance with the instructions in section 9

Title page example

G

JSC "Mosnroekt"

Fitness and health complex

General explanatory note

Director

The chief architect of the project

Form 16 - Scope of the project

Designation

Name

Note

Instructions for filling out the statement The statement indicates:

In the column "Volume number" - the number of the volume or its part;

In the column "Designation" - the designation of the document indicated on the title page, and, if necessary, the name or distinctive index of the organization that issued the document;

In the column "Name" - the name of the document in strict accordance with the name indicated on the title page;

In the column "Note" - additional information.

UDC 691:002:006.354 OKS 01.100.30 Zh 01 OKSTU0021

Keywords: working documentation, working drawings, general data on working drawings, composition, main sets, specifications, changes, binding, project documentation, graphic and text documents, title page, main inscriptions, signatures

page 1

page 2

page 3

page 4

page 5

page 6

page 7

page 8

page 9

page 10

page 11

page 12

page 13

page 14

page 15

page 16

page 17

page 18

page 19

page 20

page 21

page 22

page 23

page 24

page 25

page 26

page 27

page 28

page 29

page 30

INTERSTATE STANDARD

SYSTEM OF DESIGN DOCUMENTS FOR CONSTRUCTION

BASIC REQUIREMENTS FOR THE DESIGN
AND WORKING DOCUMENTATION

Interstate Scientific and Technical Commission
on standardization and technical regulation
and certification in construction (MNTKS)

Foreword

1 DEVELOPED by the State Enterprise - the Center for Methodology, Rationing and Standardization in Construction (GP CNS) of the Gosstroy of Russia

INCLUDED by the Department for the Development of Scientific and Technical Policy and Design and Survey Works of the Gosstroy of Russia

2 ADOPTED by the Interstate Scientific and Technical Commission for Standardization, Technical Regulation and Certification in Construction (ISTCS) on December 10, 1997

3 INTRODUCED from April 1, 1998 as the state standard of the Russian Federation by the Decree of the Gosstroy of Russia dated December 29, 1997 No. 18-75

1 area of ​​use. 2 3. General requirements for the composition of the documentation. 2 4 General requirements for completing documentation. 3 4.1 Design documentation. 3 4.2 Working drawings. 3 General data on working drawings .. 4 5. General rules for the implementation of documentation. 5 coordination axes. 5 Application of dimensions, slopes, marks, inscriptions. 6 Images (sections, sections, views, fragments) 7 Basic inscriptions. 9 6 Rules for the implementation of specifications on the drawings. 9 7. Rules for making changes to the working documentation issued to the customer. 9 7.4. Permission to make changes. 10 7.5. Alteration. 10 8. Rules for binding working documentation. 13 9 Rules for the design of bound documentation. 14 Appendix A. Stamps of the main sets of working drawings. 14 Appendix B. Forms 1-2 - Sheets of general data on working drawings .. 15 Appendix B. List of ESKD standards to be taken into account when performing graphic and text documentation for construction. 16 Appendix D. List of allowed word abbreviations (addition to GOST 2.316) 17 Appendix D. Forms 3-6 - Main inscriptions and additional columns to it. 18 Appendix E. Location of the main inscription, additional columns to it and dimensional frames on the sheets. 20 Appendix G. Forms 7-8 - Specifications. 21 Appendix I. Form 9 - Permission to make changes. 21 Appendix K. Form 10 - Table of registration of changes. 22 Annex L. Form 11 - Stamp of cancellation (replacement) of sheets of the original document. 22 Appendix M Forms 12-13 - Anchor Stamps (First and Subsequent Sheets) 23 Annex H. Form 14 - Cover. 23 Appendix P. Form 15 - Title page. Title page example. 24 Annex R. Form 16 - Project composition. 25

INTERSTATE STANDARD

Introduction date 1998-04-01

1 area of ​​use

This standard establishes the basic requirements for design and working documentation for the construction of enterprises, buildings and structures for various purposes.

The general rules for the implementation of graphic and text documentation, established in section 5 of this standard, also apply to reporting technical documentation on engineering surveys for construction.

2 Normative references

c) sketch drawings of general views of non-standard products in accordance with GOST 21.114 *;

* Perform if necessary.

d) specifications of equipment, products and materials in accordance with GOST 21.110;

e) other attached documentation provided for by the relevant standards of the Design Documentation System for Construction (SPDS);

f) estimate documentation according to the established forms.

4 General requirements for completing documentation

4.1 Design documentation

4.1.1 Project documentation intended for approval (stage-project, approved part of the working draft) is completed in volumes, as a rule, in separate sections provided for by building codes and regulations. Each volume is numbered with Arabic numerals.

Example- Volume 1 - General Explanatory Note

Volume 2 - Master Plan and Transport

If necessary, the volume is divided into parts. In this case, the volumes are numbered by type: Volume 1.1, Volume 1.2.

4.1.2 Text and graphic materials included in the volume are completed, as a rule, in the following order:

Cover;

Title page;

Project composition:

Explanatory note;

Basic drawings provided by building codes and regulations.

The rules for the design of the cover, title page, content and composition of the project are given in section 9.

4.1.3 Each text and graphic document included in the volume is assigned a designation, which is indicated on the title page and in the main inscriptions.

The composition of the designation includes the basic designation, established according to the system in force in the organization, and through a hyphen - the brand and / or code of the project section. Marks of sections of the project are taken by analogy with the marks of the main sets of working drawings given in Appendix A.

Examples

1 2345-PZ Section "General Explanatory Note"

2 2345-GT Section "Master Plan and Transport"

3 2345-12-AC Section "Architectural and construction solutions",

ПЗ - cipher of the project section;

GT and AC - marks of sections of the project.

4.1.4 Text and graphic materials, as a rule, include the volume on sheets folded according to the A4 format GOST 2.301.

Each volume includes no more than 250 A4 sheets, 150 A3 sheets, 75 A2 sheets and 50 A1 sheets.

4.1.5 General requirements for the implementation of graphic documentation are given in Section 5.

Text documents are performed in accordance with GOST 2.105, taking into account the requirements of section 5 of this standard.

4.2 Working drawings

4.2.1. Working drawings intended for the production of construction and installation works are combined into sets (hereinafter referred to as the main sets) by brand in accordance with Appendix A.

4.2.2. The main set of working drawings of any brand can be divided into several main sets of the same brand (with the addition of a serial number to it) in accordance with the process of organizing construction and installation work.

Example- AC1; AC2; QOL1; QOL2.

4.2.3. Each main set of working drawings is assigned a designation, which includes the basic designation established according to the system in force in the organization, and through a hyphen - the brand of the main set.

Example- 2345-12-AP,

where 2345 is the number of the agreement (contract) or the code of the construction object;

12 - number of the building or structure according to the general plan *;

2345-12 - basic designation;

AP - brand of the main set of working drawings.

* For sections of the project related to the construction site as a whole (general explanatory note, master plan and transport, etc.), as well as for working drawings of linear structures, master plan, external communications, this part of the basic designation is usually excluded.

4.2.4. The main sets of working drawings include general data on working drawings, as well as drawings and diagrams provided for by the relevant SPDS standards.

General data on working drawings

4.2.5. On the first sheets of each main set of working drawings, general data on working drawings are given, including:

a) a list of working drawings of the main set in form 1;

b) a list of reference and attached documents in form 2;

c) a list of the main sets of working drawings in form 2;

d) a list of specifications (if there are several layouts in the main set), performed according to Form 1;

e) symbols that are not established by state standards, and the meanings of which are not indicated on other sheets of the main set of working drawings;

e) general instructions;

g) other data provided by the relevant SPDS standards.

Forms 1 and 2 with instructions for completing them are given in Appendix B.

4.2.6 The list of working drawings of the main set contains a sequential list of sheets of the main set.

4.2.7 The list of reference and attached documents is compiled by sections:

a) reference documents;

b) attached documents.

In the "Referenced Documents" section, indicate the documents that are referenced in the working drawings, including:

a) drawings of typical structures, products and assemblies indicating the name and designation of the series and issue number;

b) standards, which include drawings intended for the manufacture of products, indicating their name and designation.

The design organization issues reference documents to the customer only under a separate agreement.

The Attached Documents section includes documents developed in addition to the working drawings of the main set, including:

Working documentation for construction products;

Sketch drawings of general views of non-standard products *;

Specification of equipment, products and materials;

local estimate;

Other documentation provided by the relevant SPDS standards.

* Perform if necessary.

The design organization issues the attached documents to the customer simultaneously with the main set of working drawings.

4.2.8 A list of the main sets of working drawings is given on the sheets of general data of the main set of the leading brand **.

** The main set of working drawings is appointed by the general designer as the leading brand.

If there are several main sets of working drawings of the same brand, a list of sets of this brand is compiled in form 2 of Appendix B, which is given on the sheet of general data for each of these sets.

4.2.9 The general instructions give:

a) the basis for the development of working documentation (design assignment, approved project);

b) the mark taken in the working drawings of a building or structure conditionally as zero (as a rule, they are given on architectural and construction drawings);

c) a record of the results of the check for patentability and patent purity of technological processes, equipment, devices, structures, products and materials for the first time used or developed in the project, as well as the numbers of copyright certificates and applications for which decisions were made to issue copyright certificates for those used in the working documentation of the invention;

d) a record that the working drawings are developed in accordance with applicable norms, rules and standards;

e) a list of types of work for which it is necessary to draw up certificates of examination of hidden work;

f) information about who owns this intellectual property (if necessary);

g) other necessary instructions.

General instructions should not repeat the technical requirements placed on other sheets of the main set of working drawings, and describe the technical solutions adopted in the working drawings.

5. GENERAL RULES FOR DOCUMENTATION

5.1. When performing design, working and other technical documentation intended for the construction of enterprises, buildings and structures, one should be guided by the requirements of the SPDS standards, as well as the standards of the unified system for design documentation (ESKD).

The list of ESKD standards to be taken into account when performing graphic and text documentation for construction is given in Appendix B.

Documentation intended for microfilming must comply with the requirements of the "Reprography" system of standards.

5.2. The drawings are performed at the optimal scale, taking into account their complexity and richness of information.

The scales in the drawings are not indicated, with the exception of product drawings and other cases provided for in the relevant SPDS standards.

5.3 The list of abbreviations of words allowed in the main inscriptions, technical requirements, tables, drawings and specifications is compiled in addition to GOST 2.316 and is given in Appendix D.

Coordination axes

5.4 On the image of each building or structure, the coordination axes are indicated and an independent notation system is assigned to them.

Coordination axes are applied to the images of the building, structures with thin dash-dotted lines with long strokes, denoted by Arabic numerals and capital letters of the Russian alphabet (with the exception of the letters: Ё, Z, Y, O, X, C, H, SH, b, Y, b) in circles with a diameter of 6 - 12 mm.

Omissions in numerical and alphabetic (except for those indicated) designations of the coordination axes are not allowed.

5.5 The numbers indicate the coordination axes along the side of the building and structures with a large number of axes. If there are not enough letters of the alphabet to designate the coordination axes, subsequent axes are designated by two letters.

Example - AA; BB; BB.

5.6 The sequence of numerical and alphabetic designations of the coordination axes is taken according to the plan from the right to the right and from the bottom up (Figure 1 A) or as shown in figures 1 b, V.

5.7 The designation of the coordination axes, as a rule, is applied on the left and lower sides of the plan of the building and structure.

If the coordination axes of the opposite sides of the plan do not coincide, the designations of these axes at the divergence points are additionally applied on the upper and / or right sides.

5.8 For individual elements located between the coordination axes of the main supporting structures, additional axes are applied and denoted as a fraction:

above the line indicate the designation of the previous coordination axis;

under the line - additional serial number within the area between adjacent coordination axes in accordance with Figure 1 G.

It is allowed to assign numerical and alphabetic designations to the coordinating axes of half-timbered columns in continuation of the designations of the axes of the main columns without an additional number.

Drawing 1

5.9 On the image of a repeating element attached to several coordination axes, the coordination axes are designated in accordance with Figure 2:

"a" - with the number of coordination axes not more than 3;

"b" - "" "" more than 3;

"c" - for all alphabetic and digital coordination axes.

If necessary, the orientation of the coordination axis to which the element is attached, in relation to the neighboring axis, is indicated in accordance with Figure 2 G.

Drawing 2

5.10 To designate the coordination axes of block sections of residential buildings, the index "c" is used.

Example - 1s, 2s, As, Bs.

On the plans of residential buildings composed of block sections, the designations of the extreme coordination axes of the block sections are indicated without an index in accordance with Figure 3.

Drawing 3

Application of dimensions, slopes, marks, inscriptions

5.11 The dimension line at its intersection with extension lines, contour lines or center lines is limited by serifs in the form of thick main lines 2–4 mm long, drawn at an angle of 45 ° to the right at an angle of 45 ° to the dimension line by 1–3 mm.

When applying a diameter or radius dimension inside a circle, as well as an angular dimension, the dimension line is limited by arrows. Arrows are also used when dimensioning radii and internal fillets.

5.12 Marks of levels (heights, depths) of structural elements, equipment, pipelines, air ducts, etc. from the reference level (conditional "zero" mark) are indicated by a conventional sign in accordance with Figure 4 and are indicated in meters with three decimal places separated from the integer by a comma .

The “zero” mark, usually taken for the surface of any structural element of a building or structure located near the planning surface of the earth, is indicated without a sign; marks above zero - with a "+" sign; below zero - with a "-" sign.

On views (façades), sections and sections, marks indicate extension lines or contour lines in accordance with Figure 5, on plans - in a rectangle in accordance with Figure 6, except as otherwise specified in the relevant SPDS standards.

Drawing 4 Figure 5 Figure 6

5.13 On the plans, the direction of the slope of the planes is indicated by an arrow, above which, if necessary, the slope is indicated as a percentage in accordance with Figure 7 or as a ratio of height and length (for example, 1:7).

It is allowed, if necessary, to indicate the value of the slope in ppm, as a decimal fraction with an accuracy of the third decimal place. In the drawings and diagrams, in front of the dimension number that determines the magnitude of the slope, a “Д sign is applied, the acute angle of which should be directed towards the slope.

The designation of the slope is applied directly above the contour line or on the shelf of the leader line.

5.14 Remote inscriptions for multilayer structures should be made in accordance with Figure 8.

Drawing 7 Drawing 8

5.15 Position numbers (brands of elements) are applied on the shelves of leader lines drawn from the images of the component parts of the object, next to the image without a leader line or within the contours of the depicted parts of the object in accordance with Figure 9.

With a small-scale image, leader lines end without an arrow and a dot.

Drawing 9

5.16 The font size for designating the coordination axes and positions (marks) should be one or two numbers larger than the font size adopted for dimensional numbers in the same drawing.

Images (sections, sections, views, fragments)

5.17 Sections of a building or structure are designated by Arabic numerals sequentially within the main set of working drawings.

Independent numbering is allowed only for sections of individual sections of a building, structure or installation, all drawings of which are placed on one sheet or group of sheets, and if these drawings do not contain references to sections located on other sheets of the main set of working drawings.

It is allowed to designate cuts in capital letters of the Russian alphabet.

The direction of view for a section according to the plan of a building and structure is taken, as a rule, from bottom to top and from right to left.

5.18 If separate parts of the view (facade), plan, section require a more detailed image, then additionally carry out remote elements - nodes and fragments.

5.19 When depicting a node, the corresponding place is marked on the view (facade), plan or section with a closed solid thin line (usually a circle or an oval) with the designation on the shelf of the leader line of the serial number of the node in Arabic numeral in accordance with Figure 10.

Drawing 10

Drawing 11

If the node is placed on another sheet, then the sheet number is indicated under the leader line shelf (Figure 10 A) or on the shelf of the leader line nearby, in brackets, in accordance with Figure 10 b.

If necessary, references to a node placed in another main set of working drawings, or to a typical node, indicate the designation and sheet number of the corresponding main set of working drawings in accordance with Figure 10 V or a series of working drawings of typical units and issue number in accordance with Figure 10 G.

Above the image of the node indicate in the circle its serial number in accordance with Figure 12 A or 12 b.

The node, which is a complete mirror image of another (main) performance, is assigned the same serial number as the main performance, with the addition of the index "n".

5.20 Fragments of plans, sections, facades, as a rule, are marked with a curly bracket in accordance with Figure 13.

Under the curly brace, as well as above the corresponding fragment, the name and serial number of the fragment are applied. If the fragment is placed on another sheet, then they give a reference to this sheet.

Figure 12 Figure 13

5.21 Images up to the axis of symmetry of symmetrical plans and facades of buildings and structures, layouts of structural elements, plans for the location of technological, energy, sanitary and other equipment are not allowed.

5.22 If the image (for example, a plan) does not fit on a sheet of the accepted format, then it is divided into several sections, placing them on separate sheets.

In this case, on each sheet where an image section is shown, a diagram of the whole image is given with the necessary coordination axes and a symbol (shading) of the image section shown on this sheet in accordance with Figure 14.

Note - If the drawings of image sections are placed in different main sets of working drawings, then the designation of the corresponding main set is indicated above the sheet number (according to 4.2.2).

Drawing 14

5.23 If the floor plans of a multi-storey building have slight differences from each other, then the plan of one of the floors is completely fulfilled, for other floors, only those parts of the plan that are necessary to show the difference from the plan depicted in full are performed.

Under the name of the partially depicted plan, an entry is given:

"For the rest, see the plan (name of the fully depicted plan)."

5.24 In the names of the floor plans of the building and structure indicate the mark of the finished floor or the number of the floor, or the designation of the corresponding cutting plane.

Examples

1 Elevation plan 0.000

2 Plan 2 - 9 floors

3 Plan 3-3

When executing a part of the plan, the title indicates the axes that limit this part of the plan.

Example- Plan for elev. 0.000 between axes 1 - 8 and A - D

It is allowed to indicate the purpose of the premises located on the floor in the title of the floor plan.

5.25 In the names of the sections of the building (structure) indicate the designation of the corresponding secant plane.

Example- Section 1-1

5.26 The names of the facades of buildings and structures indicate the extreme axes between which the facade is located.

Example- Facade 1-12

Basic inscriptions

5.27 Each sheet of a graphic and text document must have a main inscription and additional columns to it. The forms of the main inscriptions and instructions for filling them out are given in Appendix D.

5.28 In the design and working documentation, the main inscription is drawn up:

1) on sheets of the main sets of working drawings and main drawings of project documentation - in accordance with Form 3;

b) on the first sheet of drawings of building products - in form 4;

c) on the first sheets of text documents and sketch drawings of general types of non-standard products - in form 5;

d) on subsequent sheets of drawings of building products and text documents and sketch drawings of general views - in form 6.

It is allowed on the first sheet of the drawing of a building product to carry out the main inscription according to form 5.

5.29 In the reporting technical documentation based on the results of engineering surveys, the main inscription is drawn up:

a) on sheets of graphic documents used in the design as a basis - in form 3;

b) on the first sheets of graphic and text documents - in form 5, on subsequent sheets - in form 6.

5.30 The location of the main inscription and additional columns to it, as well as dimensional frames on the sheets are given in Appendix E.

5.31 The main inscriptions, additional columns to them and frames are made with solid thick main and solid thin lines in accordance with GOST 2.303 in accordance with Appendix D.

5.32 Graphic and text documents, brochured in the form of a volume, album, issue or in other publishing form, are issued with a title page.

Rules for the execution of the title page are given in section 9.

5.33 It is allowed for the title page not to carry out and not to brochure the text working documents of a small volume. In this case, the first sheet of the document is drawn up with the main inscription in form 3, the subsequent ones - in form 6.

6 Rules for making specifications on drawings

6.1. To the layout of the elements of a prefabricated structure, a monolithic reinforced concrete structure, to the drawings of installations (blocks) of technological, sanitary and other equipment, a specification is drawn up in form 7 of Appendix G.

When drawing drawings by the group method, group specifications are compiled in form 8 of Appendix G.

6.2. Specifications for building products are according to GOST 21.501.

7. Rules for making changes to the working documentation issued to the customer

7.1. A change in a working document previously issued to a customer is any correction, deletion or addition of any data to it without changing the designation of this document. The designation of the document may be changed only in the case when different documents are erroneously assigned the same designations or an error is made in the designation of the document.

7.2. Changes are made to the original document. Changes to the calculations are not allowed.

7.3. Copies of sheets (modified, additional and issued instead of replaced sheets) of working documentation are sent to organizations to which copies of documents were previously sent, simultaneously with copies of the general data of the corresponding main set of working drawings, specified in accordance with 7.5.

7.4. Permission to make changes

7.4.1. The change of the document is carried out on the basis of the permission to make changes (hereinafter referred to as the permission), drawn up in accordance with Form 9 of Appendix I.

The permission is approved by the head of the organization that developed the document or, on his behalf, another official.

7.4.2. The basis for obtaining original documents for making changes to them is permission.

7.4.3. Changes for each document (for example, the main set of working drawings, specification of equipment, products and materials) are issued with a separate permit.

It is allowed to make one general permission for changes made simultaneously to several documents, if the changes are interconnected or the same for all changed documents.

7.5. Alteration

7.5.1. Changes to the original documents are made by crossing out or erasing (washing). This takes into account the physical condition of the original.

7.5.2. After making changes, the images, letters, numbers, signs must be clear, the thickness of the lines, the size of the gaps, etc. must be performed according to the rules provided for by the relevant standards of the ESKD and the Reprography standards system.

7.5.3. Changeable sizes, words, signs, inscriptions, etc. cross out with solid thin lines and next put down new data.

7.5.4. When the image (part of the image) is changed, it is outlined with a solid thin line forming a closed contour, and crossed out crosswise with solid thin lines.

A new image of the changed area is performed on a free field of the sheet or on another sheet without rotation.

7.5.5. Changed, canceled and additional sections of the image are assigned a designation consisting of the serial number of the next change in the document and through the point of the serial number of the changed (cancelled, additional) image section within this sheet. In this case, the new image of the changed area is assigned a change designation of the replaced image.

If a new image of the changed area is placed on another sheet, then the designation of the change assigned to it is saved and is not taken into account in the change table of this sheet.

7.5.6. Near each change, including near the change corrected by erasing (washing), outside the image, the designation of the change is applied in a parallelogram in accordance with Figure 15.

Drawing 15

Draw a solid thin line from the parallelogram to the modified area.

7.5.7. Closely spaced altered sizes, words, signs, inscriptions, etc. encircle with a solid thin line forming a closed contour, without crossing out in accordance with Figure 16.

7.5.8. If a new image of the changed area is placed on another sheet, then the replaced image also indicates the number of the sheet on which the new image is located in accordance with Figure 17.

7.5.9. Above the new image of the changed area, the designation of the change in the replaced image is placed in a parallelogram, and with the parallelogram they indicate: "Instead of the crossed out one."

If a new image of the changed area is placed on another sheet, then with a parallelogram indicate: "Instead of the crossed out on the sheet (number of the sheet on which the replaced image is located)" in accordance with Figure 18.

7.5.10. If a new image of the changed area is placed near the replaced one, then they are connected by leader lines with the designation of the change in accordance with Figure 19.

Figure 16 Figure 17

Drawing 18

Drawing 19

Above the additional image, the designation of the change is placed in the parallelogram, and with the parallelogram they indicate: "Addition" in accordance with Figure 20.

Drawing 20

7.5.11. When an image (part of an image) is canceled, the following is indicated when indicating the change: “Cancelled”.

7.5.12. If there is not enough space to make changes or there may be a violation of the clarity of the image during correction, then a new original is made taking into account the changes made and its previous designation is retained.

If one or more sheets of the original are replaced or added, then the inventory number assigned to the original is stored on them.

When replacing all sheets of the original, it is assigned a new inventory number.

7.5.13. When making changes to the sheets of the main set of working drawings in the list of working drawings of this set, on the sheets of general data in the "Note" column indicate:

a) when making the first change - “Change. 1".

When making subsequent changes, additionally the next number of changes, separating them from the previous ones with a semicolon.

Example- Change. 1; 2; 3

b) on replaced sheets with the change number - “(Replacement)”.

Example- Change. 1 (Deputy)

c) on canceled sheets with the change number - “Cancelled”.

Example- Change. 1 (Cancelled)

d) on additional sheets with the change number - “(New)”.

Example- Change. 1 (New)

7.5.14. If additional sheets are included in the main set of working drawings, then they are assigned successive serial numbers and recorded in continuation of the sheet of working drawings of the corresponding main set.

If there is not enough space in the list of working drawings to record additional sheets, the continuation of the sheet is transferred to the first of the additional sheets. At the same time, at the end of the statement of working drawings placed in the “General Data”, an entry is made: “Continuation of the statement, see sheet (sheet number)”, and a heading is placed above the statement on an additional sheet: “The statement of working drawings of the main set (Continued)” .

The numbers and names of the canceled sheets in the list of working drawings are crossed out.

When changing the names of sheets, make the appropriate changes in the column "Name".

7.5.15. When changing the total number of sheets of a document on its first sheet in the main inscription, the corresponding changes are made in the “Sheets” column.

7.5.16. When performing additional and canceling previously completed attached documents, corrections are made to the list of reference and attached documents of the corresponding main set of working drawings.

7.5.17. When performing additional and canceling previously completed main sets of working drawings, corrections are made to the list of main sets of working drawings.

7.5.18. The changes made to the original are indicated in the table of changes placed in the title block.

It is allowed to place the table of changes outside the main inscription (above it or to the left of it) in the same form.

7.5.19. The change table indicates:

a) in the column "Change." - sequence number of the document change;

b) in the column "Number. account" - the number of variable areas of the image on this sheet within the next change;

c) in the column "Sheet" - on sheets issued instead of replaced ones - "Deputy", on sheets added again - "New".

When replacing all sheets of the original (with the next serial number of the document change), on the first sheet in the column "Sheet" indicate "All". At the same time, the table of changes on other sheets of this original is not filled out.

In other cases, a dash is put in the "Sheet" column;

d) in the column "Document No." - designation of permission;

e) in the column "Sub." - the signature of the person responsible for the correctness of the change (the signature of the person responsible for normative control is put on the field for filing the sheet);

f) in the column "Date" - the date of the change.

7.5.20. The table of changes does not take into account corrections made to the statements of the general data sheet in connection with changes to the sheets of the main set and attached documents.

5.5.21. When making changes to text documents, it is recommended to follow the change registration table in form 10 of Appendix K. The change registration table is placed on the title page of the text document.

7.5.22. Significant changes in text documents are made in one of the following ways:

a) replacement of all or individual sheets of the document;

b) issuance of new additional sheets.

When changing the original text documents, it is allowed, when adding a new sheet, to assign it the number of the previous sheet with the addition of the next Arabic numeral, separating it from the previous point.

Example - 3.1

In this case, the total number of sheets is changed on the first sheet.

In text documents containing mostly solid text, when adding a new item, it is allowed to assign the number of the previous item to it with the addition of the next lowercase letter of the Russian alphabet, and when canceling the item, keep the numbers of subsequent items.

7.5.23. When canceling or replacing a document, all canceled and replaced sheets of the original are crossed out crosswise with solid thin lines and a stamp is put down in the form 11 of Appendix L.

8. Rules for linking working documentation

8.1. Working documentation - standard designs, standard design solutions (intended for binding) and working documentation for re-use are subject to binding to a specific construction site. On each sheet of the attached documentation, a binding stamp is put in accordance with Appendix M:

a) on the first sheet - in form 12;

b) on subsequent sheets - according to form 13.

8.2. Covers and title pages of the main sets of working drawings of standard projects (standard design solutions), published in the form of albums and releases, are not tied and are not sent to the customer.

8.3. Anchor stamp is applied to the free field of the sheet, preferably above the main inscription or to the left of it.

8.4. It is allowed not to put a binding stamp on unchangeable working drawings of structures, products and assemblies in case they are re-used by the organization that developed and approved these drawings. The specified working drawings are recorded in the section of the attached documents without changing the designation.

8.5. Changes during binding are made in accordance with 7.5.1 - 7.5.4, 7.5.14 - 7.5.17 and taking into account the following additional requirements:

a) if there are two or more variable areas of the image, then they are assigned serial numbers, which are put down in Roman numerals on the shelf of the leader line in accordance with Figure 21;

b) above the changed area, indicate in Roman numeral the serial number of the changed area of ​​the image and the inscription "Instead of crossed out" in accordance with Figure 22.

Drawing 21 Drawing 22

If a new image (part of an image) is placed on another sheet, then the number of the sheet on which the new image is located is also indicated for the replaced image.

8.6. The main inscriptions on the sheets of attached documentation, published in the form of albums and releases, are left unchanged.

8.8. The canceled sheets are excluded from the attached documentation without changing the general numbering of the sheets.

9 Bound Documentation Rules

9.1 Each bound document is issued with a cover in the form 14 given in Appendix H. The cover is not numbered and is not included in the total number of pages.

9.2 The first page of a text (graphic) document or several bound documents is the title page. The title page is performed according to the form 15 of Appendix P. An example of filling out the title page is given in the same place.

9.3 All pages of a bound document, starting with the title one, must have continuous page numbering. The title page is not numbered.

The page number on sheets of text and graphic documents is indicated in the upper right corner of the working field of the sheet.

In addition, in the main inscription of text and graphic documents included in a volume, album or release and having an independent designation, indicate the serial numbering of sheets within the document with one designation.

9.4 When compiling several documents in the form of a volume, album or release, after the title page, the “Contents” are given, which is performed in the form 2 of Appendix B.

The first sheet of the "Contents" is drawn up with the main inscription in accordance with form 5 of Appendix D, the subsequent ones - in form 6 of Appendix D. The "Contents" are assigned a designation consisting of the designation of the document and the code "C".

Example- 2345-GT.S, 2345-11-KZh.IS, 2345-11TH.NS

9.5 Title pages of design documents are signed by:

manager or chief engineer of the organization;

chief engineer (architect) of the project.

The title pages of working documents are signed by the responsible person - the chief engineer (architect) of the project.

The title page of the reporting survey documentation is drawn up taking into account the additional requirements of the relevant building codes and regulations.

9.6 The composition of the project, according to 4.1.2, is given in the statement executed in the form 16 of Appendix P.

The statement provides a sequential list of volumes of project documentation.

The first sheet of the statement is drawn up with the main inscription in form 5 of Appendix D, the subsequent ones - in form 6 of Appendix D.

The statements are assigned a designation consisting of the basic designation of the document and through a hyphen - the code "SP".

Example- 2345-SP

Stamps of the main sets of working drawings

Table A.1

Name of the main set of working drawings		Note
Production technology
Technological communications		When combining all technological communications
General plan and transport facilities		When combining the working drawings of the master plan and transport facilities
General plan
Architectural solutions
Interiors		Working drawings can be combined with the main set of brand AP or AC
Reinforced concrete structures
Wooden structures
Architectural and construction solutions		When combining working drawings of architectural solutions and building structures
Detailed metal structures
Water supply and sewerage
Heating, ventilation and air conditioning
Thermal mechanical solutions for boiler rooms
Air supply
dust removal
Refrigeration
Gas supply (internal devices)
Power equipment
Electric lighting (internal)
Communication systems
Radio communications, broadcasting and television
Firefighting
Fire alarm
Security and fire alarm systems
Hydraulic Solutions
Automation…		The ellipsis is replaced by the name and brand of the corresponding main set of working drawings
Integrated automation		When combining working drawings of various technological processes and engineering systems
Anticorrosive protection of structures of buildings, structures
Thermal insulation of equipment and pipelines
Railways
Car roads
Transport facilities		When combining working drawings of roads, railways and other roads
External water supply and sewerage networks		When combining working drawings of external water supply and sewerage networks
Thermal mechanical solutions for heating networks
Outdoor gas pipelines
Outdoor electric lighting
Power supply
Note - If necessary, additional brands of the main sets of working drawings can be assigned. At the same time, capital letters (no more than three) of the Russian alphabet are used for stamps, corresponding, as a rule, to the initial letters of the names of the main set of working drawings.

APPLICATIONB
(mandatory)

Sheets of general data on working drawings

Form 1 - List of working drawings of the main set

Specification Sheet

Directions By filling statements workers drawings main kit

In the statement of working drawings of the main set indicate:

a) in the column "Sheet" - the serial number of the sheet of the main set of working drawings;

b) in the column "Name" - the name of the images placed on the sheet, in strict accordance with the names given in the main inscription of the sheet;

c) in the column "Note" - additional information, for example, about changes made to the working drawings of the main set.

Directions By filling statements specifications

The specification sheet indicates:

a) in the column "Sheet" - the number of the sheet of the main set of working drawings on which the specification is placed;

b) in the column "Name" - the name of the specification in full accordance with its name indicated on the drawing;

c) in the column "Note" - additional information, incl. about changes to the specifications.

Form 2 - List of main sets of working drawings.

List of referenced and attached documents

Directions By filling statements major kits workers drawings

In the statement of the main sets of working drawings indicate:

a) in the column "Designation" - the designation of the main set of working drawings and, if necessary, the name or distinctive index of the organization that issued the document;

b) in the column "Name" - the name of the main set of working drawings;

c) in the column "Note" - additional information, incl. on changes in the composition of the main sets of working drawings.

Directions By filling statements reference And attached documents

In the statement of reference and attached documents indicate:

a) in the column "Designation" - the designation of the document and, if necessary, the name or distinctive index of the organization that issued the document;

b) in the column "Name" - the name of the document in strict accordance with the name indicated on the title page or in the main inscription;

c) in the column "Note" - additional information, incl. on the changes made to the recorded documents included in the working documentation.

APPENDIX B
(mandatory)

List of ESKD standards to be taken into account when performing graphic and text documentation for construction

Table B.1

Designation and name of the standard	Conditions for applying the standard
ESKD. General requirements for the implementation of design and technological documents on printing and graphic output devices of a computer	ESKD. Product types	ESKD. Types and completeness of design documents	ESKD. General requirements for text documents	Subject to the requirements of sections 4, 5 and 9 of this standard
ESKD. Specification	Taking into account the requirements of section 6 of this standard and GOST 21.501
ESKD. Basic requirements for drawings	ESKD. Group and basic design documents
ESKD. Specifications	Subject to the requirements of 5.27, 5.28, 5.30 - 5.32 of section 5 and section 9 of this standard. 3.7.1 and 3.8 GOST 2.114 do not take into account
ESKD. Formats	ESKD. Scales
ESKD. lines	ESKD. Drawing fonts	ESKD. Images - views, cuts, sections	Subject to the requirements of 5.17 - 5.26 of this standard
ESKD. Designations of graphic materials and the rules for their application on the drawings	ESKD. Application of dimensions and limit deviations	Subject to the requirements of 5.11 - 5.13 of this standard
ESKD. Indication on the drawings of the tolerances of the shape and location of surfaces
ESKD. Rules for the execution of drawings of metal structures	ESKD. Accounting and storage rules	In terms of the form of the inventory book, subscriber card and instructions for folding copies of drawings
Note - The conditions for the application of ESKD standards of classification group 7 are determined by the corresponding standards of SPDS

APPENDIX D

(obligatory)

List of allowed word abbreviations (addition to GOST 2.316)

Full name	Reduction
Highway
Anti-seismic seam
Architect
asphalt concrete	asph. bet.
Concrete, concrete
ventilation chamber	ventilation chamber
Chief Engineer	Ch. eng. (*)
Chief engineer (architect) of the project	GIP (GAP) (*)
Chief Specialist	Ch. specialist. (*)
Expansion joint
Director
Document
allowed
Unit	Unit rev. (T)
	Capacity (c, t)
Railway
Reinforced concrete, reinforced concrete
manager
insulation, insulating
Institute
Design
Coefficient
Efficiency
Staircase, stairway
Workshop (in design institutes)
materials	materials (t)
Mounting
norms. load
Equipment
checked
calc. load
Sanitary	dignity. tech.
Toilet	dignity. node
Well
Snow
Temperature joint
Technological
Rail head level	ur. r. (And)
Ground level
Clean floor level	ur. ch.p. (i)
Fundamental
Cement, cement
cement concrete	cement. bet.
Plaster
Crushed stone, crushed stone
Electric
	e-t (i. t)
Note - Abbreviations marked with (*) are used only in the title block; (t) - in tables; (c) - with numbers or ciphers; (i) - on graphic images

APPENDIX E
(mandatory)

Main inscriptions and additional columns to it

Form 3 - For sheets:

main sets of working drawings;

main drawings of sections of project documentation;

graphic documents on engineering surveys

Form 4 - For drawings of building products (first sheet)

Form 5 - For all types of text documents

Notes e - The main inscription in form 5 can be used for graphic documents on engineering surveys that are not used as a base

Form 6 - For drawings of building products and all types of textdocuments (subsequent sheets)

Directions By filling basic inscriptions And additional graph To her

In the columns of the main inscription and additional columns to it (the numbers of the columns are indicated in brackets) lead:

a) in column 1 - the designation of the document, including the project section, the main set of working drawings, product drawing, text document, etc.;

b) in column 2 - the name of the enterprise, housing and civil complex or other construction object, which includes the building (structure), or the name of the microdistrict;

c) in column 3 - the name of the building (structure) and, if necessary, the type of construction (reconstruction, expansion, technical re-equipment, overhaul);

d) in column 4 - the name of the images placed on this sheet, in exact accordance with their name on the drawing.

The names of specifications and other tables, as well as textual indications related to images, are not indicated in the column;

e) in column 5 - the name of the product and / or the name of the document;

f) in column 6 - designation of the design stage:

1) P - for project documentation, including the approved part of the working draft;

2) P - for working documentation;

g) in column 7 - the serial number of a sheet or page of a text document for duplex printing. On documents consisting of one sheet, the column is not filled out;

i) in column 8 - the total number of sheets of the document. The column is filled out only on the first sheet. On the first sheet of a text document for duplex printing indicate the total number of pages;

j) in column 9 - the name or distinctive index of the organization that developed the document;

k) in column 10 - the nature of the work (developed, checked, normative control).

Depending on the design stage, the complexity and significance of the document, it is allowed to fill in free lines at the discretion of the organization's management (indicate the positions of persons responsible for the development of the document (drawing);

l) in columns 11 - 13 - the names and signatures of the persons indicated in column 10, and the date of signing.

Signatures of other officials and coordinating signatures are placed on the field for filing the sheet;

m) in columns 14 - 19 - columns of the table of changes, which are filled in in accordance with 7.5.19;

o) in column 20 - the inventory number of the original;

p) in column 21 - the signature of the person who accepted the original for storage, and the date of acceptance (day, month, year);

c) in column 22 - the inventory number of the original document, in exchange for which a new original was issued;

r) in column 23 - the designation of the material of the part (the column is filled out only on the drawings of the parts);

s) in column 24 - the mass of the product shown in the drawing, in kilograms, without indicating the unit of measurement. The mass of the product in other units of measurement is given with the indication of the unit of measurement.

Example- 2.4 t;

t) in column 25 - scale (put down in accordance with GOST 2.302);

w) in column 26 - the signature of the person who copied the drawing (if necessary).

APPENDIX E
(mandatory)

The location of the main inscription, additional columns to it and dimensional frames on the sheets

Notes e - Dimensions in parentheses are for the framework of standard design documentation.

APPENDIX G
(mandatory)

Form 7 - Specification

Form 8 - Group specification

Directions By filling specifications And group specifications

The specifications indicate:

a) in the column "Pos." - positions (brands) of structural elements, installations;

b) in the column "Designation" - the designation of the main documents for the structural elements, equipment and products recorded in the specification or standards (technical specifications) for them;

c) in the column "Name" - the names of structural elements, equipment and products and their brands. It is allowed to indicate the name of a group of elements with the same name once and underline;

d) in the column "Number." forms 7 - the number of elements. In the column "Number ..." of form 8 - instead of the ellipsis, they write "according to the scheme", "on the floor", etc., and below - the serial numbers of the layout or floors;

e) in the column "Mass, unit, kg" - mass in kilograms. It is allowed to give the mass in tons, but with an indication of the unit of measurement;

f) in the column "Note" - additional information, for example, a unit of mass.

APPENDIX AND
(mandatory)

Form 9 - Permission to make changes

Directions By filling permissions on introduction changes

Permissions indicate:

a) in column 1 - the designation of the permit, consisting of the serial number of the permit according to the book of registration of permits in accordance with GOST 21.203 and a dash of the last two digits of the year.

Example - 15-97;

b) in column 2 - the designation of the document in which the change is made;

c) in column 3 - the name of the enterprise under construction, building (structure);

d) in column 4 - the next serial number assigned to the changes that are made to the document by one permit. It is indicated for the entire document, regardless of how many sheets it is made on. The serial numbers of changes are indicated by Arabic numerals;

e) in column 5 - the numbers of the sheets of the document in which changes are made;

f) in column 6 - the content of the change in the form of a text description and / or graphic image;

g) in column 7 - code of the reason for the change in accordance with the table;

i) in column 8 - additional information;

j) in columns 9 - 11 - the names of the persons signing the permit, their signatures and the date of signing;

k) in column 12 - the name of the design organization and the subdivision (department) that issued the permit;

l) in columns 13 - 16 - the name of the relevant departments or organizations, positions and names of persons with whom the permit is agreed in the prescribed manner, their signatures and dates of signing, as well as the signature of the normative controller;

m) in column 17 - serial number of the permit sheet. If the permit consists of one sheet, the column is not filled out;

o) in column 18 - the total number of permit sheets.

Form 10 - Change Registration Table

Directions By filling tables registration changes

In the columns of the change registration table indicate:

a) in the columns "Change", "Document number", "Signed" and "Date" - similar to filling in the corresponding columns of the table of changes;

b) in the columns "Numbers of sheets (pages) changed, replaced, new, canceled" - the numbers of sheets (pages) respectively changed, replaced, added and canceled under this permission.

When replacing the entire document, in the column “Numbers of sheets (pages) replaced” indicate “All”;

c) in the column "Total sheets (pages) in doc." - the number of sheets (pages) in the document. The column is filled in if the columns “Numbers of sheets (pages) new” and / or “Numbers of sheets (pages) canceled” are filled in.

APPENDIX L
(mandatory)

Form 11 - Stamp of cancellation (replacement) of sheets of the original document

Directions By filling stamp cancellation (substitutions) original document

The stamp indicates:

a) in line 1 - the sequence number of the next change in the document, in accordance with which the sheet was canceled or replaced (for example, "Change 3"). When canceling the sheet, the word "Replaced" in the stamp is crossed out;

b) in columns 2 - 5 - the position, surname, signature of the person responsible for making changes, and the date of signing.

APPENDIX M
(mandatory)

Form 12 - Anchor Stamp (First Sheet)

Form 13 - Anchor Stamp (Subsequent Sheets)

Directions By filling stamps bindings

When filling in the binding stamps indicate:

a) in column 1 - the new designation of the attached document;

b) in column 2 - the name of the organization that performed the binding;

c) in column 3 - the name of the enterprise under construction, building or structure for which the binding is made;

d) in columns 4 - 7 - the positions and names of the persons responsible for the binding, as well as the person who carried out the normative control, their signatures and dates of signing;

e) in column 8 - the inventory number assigned to the linked document;

f) in column 9 - the number of sheets of the attached document;

g) in columns 10, 11 - the signature of the person who accepted the attached document for storage, and the date of signing.

APPENDIX H
(mandatory)

Form 14 - Cover

Note - The name of the governing body is indicated for state organizations.

APPENDIX P
(mandatory)

Form 15 - Title page

Notes

1 The name of the governing body is indicated for state organizations.

2 The field for signing the document is filled in in accordance with the instructions in section 9.

Title page example

APPENDIX R
(mandatory)

Form 16 - Scope of the project

Directions By filling statements

The listing indicates:

In the column "Volume Number" - the number of the volume or its part;

In the column "Designation" - the designation of the document indicated on the title page, and, if necessary, the name or distinctive index of the organization that issued the document;

In the column "Name" - the name of the document in strict accordance with the name indicated on the title page;

In the column "Note" - additional information.

Keywords: working documentation, working drawings, general data on working drawings, composition, main sets, specifications, changes, binding, project documentation, graphic and text documents, title page, main inscriptions, signatures