GOST 9433-80

Group B32

INTERSTATE STANDARD

LUBRICANT CIATIM-221

Specifications

Grease CIATIM-221. Specifications

OKP 02 5421 0800

Introduction date 1982-01-01

INTRODUCED BY DECREE State Committee USSR according to the standards of May 19, 1980 N 2188

INSTEAD OF GOST 9433-60

Decree of the State Standard of the USSR dated April 17, 1991 N 513 removed the limitation of validity

EDITION with Amendments No. 1, 2, 3, approved in August 1982, April 1986, April 1991 (IUS 11-82, 7-86, 7-91)

This standard applies to grease, designed for lubrication of friction units and mating surfaces "metal-metal" and "metal-rubber", operating at temperatures from minus 60 to plus 150 °C.

The requirements of this standard are mandatory.

(Changed edition, Rev. N 3).

1. TECHNICAL REQUIREMENTS

1.1. Lubricants shall be manufactured in accordance with the requirements of this standard, according to technological regulations and from the components that were used in the manufacture of lubricant samples that passed state tests with positive results and were approved for use in the prescribed manner.

1.2. In terms of physical and chemical parameters, CIATIM-221 grease must comply with the requirements and standards specified in the table.


Name of indicator		Test method
1. Appearance	Homogeneous ointment, smooth structure from light yellow to light brown	According to clause 4.3
2. Effective viscosity at minus 50 °C and an average strain rate gradient of 10 s, Pa s, not more than		According to GOST 7163-84
3. Tensile strength at 50 °C, Pa, not less than		According to GOST 7143-73, method B
4. Dropping point, °С, not lower		According to GOST 6793-74
5. Penetration at 25 °C, 0.1 mm		According to GOST 5346-78
6. Corrosive effect on metals	Withstands	According to GOST 9.080-77 and clause 4.4 of this standard
7. Colloidal stability, % of extracted oil, no more		According to GOST 7142-74 and clause 4.5 of this standard
8. Mass fraction of alkali in terms of NaOH,%, no more		According to GOST 6707-76 and clause 4.6 of this standard
	Absence	According to GOST 2477-65
		According to GOST 6479-73 and clause 4.7 of this standard
11. Evaporation at 150 °C for 1 hour, %, no more		According to GOST 9566-74

1.1-1.2. (Changed edition, Rev. N 1, 3).

2. SAFETY REQUIREMENTS

2.1. CIATIM-221 lubricant is inactive, does not have a toxic effect on the body, does not irritate the skin and mucous membranes.

The maximum allowable concentration of the liquid lubricant base in the air of the working area is 10 mg/m.

2.2. When working with lubrication, it is necessary to apply individual means protection in accordance with standard industry standards approved in the prescribed manner.

2.3. Persons working with lubrication should wash their hands with warm water and soap before eating, smoking and after finishing work.

2.4. The lubricant is not flammable and non-explosive, it is a combustible product of group IV. The flash point of the liquid lubricant base is above 265 °C.

When the lubricant catches fire, the following fire extinguishing agents are used: compositions SI-VK, SI-2 and SZHB-BF-2.

3. ACCEPTANCE RULES

3.1. Grease is accepted in batches.

A batch is considered to be a quantity of grease weighing up to 1000 kg, homogeneous in terms of quality, accompanied by a quality document.

(Changed edition, Rev. N 1, 2.).

3.2. Sample size - according to GOST 2517-85.

3.3. Upon receipt of unsatisfactory test results for at least one indicator, repeated tests of a newly selected sample from the same sample are carried out for it.

The retest results apply to the entire lot.

3.4. The indicator "Evaporation at 150 ° C" is determined by the manufacturer at the request of the consumer.

(Changed edition, Rev. N 2).

4. TEST METHODS

4.1. Lubrication samples are taken according to GOST 2517-85.

The mass of the combined sample is 2 kg of lubricant.

In case of disagreement in assessing the quality of the lubricant, the sample should be stored for at least five years.

4.2. Analysis of the lubricant for compliance with the requirements of this standard, except for the content of mechanical impurities, is carried out before its packaging. Mechanical impurities are determined in the lubricant packaged in containers.

4.1-4.2. (Changed edition, Rev. N 1).

4.3. For determining appearance the lubricant is applied with a spatula on a glass plate 50x70x2 mm in size according to GOST 111-90 using a template (internal dimensions 35x35 mm, thickness 2 mm) and viewed with the naked eye in transmitted light.

4.4. The corrosion test is carried out on copper plates of M0k or M1k grades according to GOST 859-2001. Discoloration and slight reddish-brown staining of the plates is allowed.

4.5. When determining colloidal stability, the ashless filter is moistened with liquid 132-24 according to GOST 10957-74. The grease is pressed out at a load of (200 ± 10) g.

4.6. When determining mass fraction alkali as a lubricant solvent, toluene of analytical grade is used. according to GOST 5789-78 and titrate the hot lubricant solution.

(Changed edition, Rev. N 2).

4.7. When determining mechanical impurities, a sample of lubricant is thoroughly mixed until a homogeneous mass is obtained with 75 cm3 of gasoline. The mixture is transferred to a separating funnel, add 75 cm 50% acetic acid according to GOST 61-75 and vigorously mixed until the lubricant is completely decomposed. After settling and separation of the layers, the lower acetic acid layer is filtered. At the end of filtration, the filter is washed three or four times with hot distilled water and dried in a thermostat, then a layer of gasoline lubricant solution is filtered through the same filter.

5. PACKAGING, LABELING, TRANSPORT AND STORAGE

5.1. Packing, marking, transportation and storage of lubricant - according to GOST 1510-84 with the following addition: the lubricant is packed in cans of tinplate and, at the request of consumers, in aluminum tubes without coating or with an internal coating of phenol-polyvinyl acetate adhesive BF-2 according to GOST 12172-74 with a capacity of 40 -200 g.

Lubricant tubes are packed in wooden or plywood boxes in rows, between the rows there should be cardboard or paper spacers.

Gross and net weights are not indicated on tubes. The batch number, month and year of manufacture of the grease are stamped.

5.2. Grease must be stored in the manufacturer's container.

5.3. (Deleted, Rev. N 3).

6. MANUFACTURER WARRANTY

6.1. The manufacturer guarantees the compliance of the grease with the requirements of this standard, subject to the conditions of transportation and storage.

6.2. Guarantee period storage in the manufacturer's container - five years from the date of manufacture.

(Changed edition, Rev. N 1).

The text of the document is verified by:
official publication
Oil products. Lubricants. Additives.
Specifications: Sat. GOSTs. -
Moscow: IPK Standards Publishing House, 2002

When looking at the digital index, it seems that this product is the development of the legendary veteran . In fact, the 221st is much closer to aircraft technology, the name of the developer obliges.

The Central Institute of Aviation Fuels and Oils did create this lubricant primarily for use in air. This confirms one of the properties of CIATIM 221: reliable operation in rarefied air, and even in high vacuum.

To match the characteristics, and exorbitant price: from the series "Ciatims" general purpose(not counting the offers of narrow specialization) this is perhaps the most expensive product.

The fundamental difference is in the base: it is organosilicon. Accordingly, the thickener consists of calcium soap.

CIATIM 221 characteristics and application

Outwardly, this lubricant differs little from its analogues: it looks like a vaseline-shaped ointment, with a smooth, shiny surface. Color from dirty yellow to light brown. The shade does not affect the characteristics of CIATIM 221 in any way, and depends only on the type of additives used by the manufacturer in accordance with GOST 9433 80.

About the properties and characteristics of CIATIM 221 lubricant - video

tensile strength of at least 120 Pa (a little, but quite enough to work on high-speed friction units);
sufficiently high dropping point: liquefaction occurs when the temperature reaches 200°C;
an interesting feature: even after the transition to a liquid state (up to boiling), the properties are restored after cooling;
The 221st does not dissolve in water, while it is excessively hygroscopic: when water is absorbed, properties change, resistance to low temperatures decreases;
virtually immune to chemical exposure, even in the form of extraneous vapors;
does not interact with rubber and polymer compounds;
maximum residual pressure at which the operating parameters do not change: not less than 666.5 Pa;
certified operating temperature range: -60°C to +150°C;
convenient for long-term stocks: properties do not change during 40 years of storage.

Such characteristics limit the use of lubricants:

Information: CIATIM 221 is non-toxic, neutral to the skin and mucous membranes, does not emit harmful vapors when heated.

What is CIATIM 221F used for?

This is a development of the 221 line, designed to level out some of the shortcomings of the base lubricant. A specially developed fluorine additive is added to the main composition.

Thanks to this, the working properties change dramatically:

Improved anti-wear and extreme pressure performance, especially under heavy load.
Increased heat resistance allows you to work in loaded nodes without loss of properties.
Eliminated hygroscopicity: this makes it possible to use in a humid environment.
Thanks to fluoroplastic inclusions, the noise during the operation of friction and rotation units is reduced.

Which is better, Litol 24 or CIATIM 221?

It is not correct to compare them as a direct analogue. "Litol" is more versatile, in addition, it does an excellent job with "water procedures".

However, the average characteristics do not make it possible to use it in loaded high-speed units: for example, precision measuring instruments.

In this sense, the 221st has no substitutes. Of course, these lubricants cannot be mixed with each other, calcium and lithium compounds are chemically incompatible.

CIATIM 201 and 221, what is the fundamental difference?

First of all, in the basis and composition of the thickener. It is these components that determine the applicability. The 201st is a typical economy class product. And the 221st is a high-tech development for use in aviation and precision instrumentation. They get along in one car (mechanism), only in different nodes.

How does it differ from 221 in terms of application?

201 should not be used in contact with rubber.
221 can operate at higher temperatures.
The shelf life differs by almost 10 times in favor of the 221st.
Accordingly, CIATIM 221 is 3-5 times more expensive.

What the real CIATIM 211 looks like from the times of the USSR - video

Group B32 STANDARD

INTERSTATE

LUBRICANT TSIAGIM-221

Specifications

Grease CIATIM-221. Specifications

OKP 02 5421 0800

By the Decree of the USSR State Committee for Standards dated May 19, 1980 No. 2188, the introduction date was set

Gosstandart Decree No. 513 dated April 17, 1991 lifted the limitation of validity

This standard applies to grease intended for lubrication of friction units and mating surfaces "metal-metal" and "metal-rubber", operating at temperatures from minus 60 to plus 150 °C.

The requirements of this standard are mandatory.

(Revised edition, Rev. No. 3).

1. TECHNICAL REQUIREMENTS

1.1. The lubricant must be manufactured in accordance with the requirements of this standard, according to the technological regulations and from the components that were used in the manufacture of lubricant samples that have passed state tests with positive results and are approved for use in the prescribed manner.

1.2. In terms of physical and chemical parameters, CIATIM-221 grease must comply with the requirements and standards specified in the table.

Name of indicator		Test method
1. Appearance	Homogeneous ointment, smooth structure from light yellow to light brown
2. Effective viscosity at minus 50 °C and an average strain rate gradient of 10 s -1 , Pa s, no more
3. Tensile strength at 50 °C, not less than
5. Penetration at 25 °C, 0.1 mm
6. Corrosive effect on metals

1.1-1.2. (Changed edition, Rev. No. 1, 3).

2. SAFETY REQUIREMENTS

2.1. CIATIM-221 lubricant is inactive, does not have a toxic effect on the body, does not irritate the skin and mucous membranes.

The maximum allowable concentration of the liquid lubricant base in the air of the working area is 10 mg/m 3 .

2.2. When working with grease, it is necessary to use personal protective equipment in accordance with standard industry standards approved in the prescribed manner.

2.3. Persons working with lubrication should wash their hands with warm water and soap before eating, smoking and after finishing work.

2.4. The lubricant is not flammable and non-explosive, it is a combustible product of group IV. The flash point of the liquid lubricant base is above 265 °C.

When the lubricant catches fire, the following fire extinguishing agents are used: compositions SI-VK, SI-2 and SZHB-BF-2.

3. ACCEPTANCE RULES

3.1. Grease is accepted in batches.

A batch is considered to be a quantity of grease weighing up to 1000 kg, homogeneous in terms of quality, accompanied by a quality document.

(Changed edition, Rev. No. 1, 2).

3.3. Upon receipt of unsatisfactory test results for at least one indicator, repeated tests of a newly selected sample from the same sample are carried out for it.

The retest results apply to the entire lot.

3.4. The indicator "Evaporation at 150 ° C" is determined by the manufacturer at the request of the consumer.

(Revised edition, Rev. No. 2).

4. TEST METHODS

4.1. Lubrication samples are taken according to GOST 2517-85.

The mass of the combined sample is 2 kg of lubricant.

In case of disagreement in assessing the quality of the lubricant, the sample should be stored for at least five years.

4.1-4.2. (Revised edition, Rev. No. 1).

4.3. To determine the appearance, the lubricant is applied with a spatula on a 50x70x2 mm glass plate according to GOST 111-90 using a template (internal dimensions 35x35 mm, thickness 2 mm) and viewed with the naked eye in transmitted light.

GOST 9433-80 S. 3

4.4. The corrosion test is carried out on plates of copper grades MOK or M1k according to GOST 859-2001. Discoloration and slight reddish-brown staining of the plates is allowed.

4.5. When determining colloidal stability, the ashless filter is moistened with liquid 132-24 according to GOST 10957-74. The grease is pressed out at a load of (200 ± 10) g.

4.6. When determining the mass fraction of alkali, toluene of analytical grade is used as a lubricant solvent. according to GOST 5789-78 and titrate the hot lubricant solution.

(Revised edition, Rev. No. 2).

4.7. When determining mechanical impurities, a sample of the lubricant is thoroughly mixed until a homogeneous mass is obtained with 75 cm 3 of gasoline. The mixture is transferred to a separating funnel, 75 cm 3 of 50% acetic acid according to GOST 61-75 are added and vigorously stirred until the lubricant is completely decomposed. After settling and separation of the layers, the lower acetic acid layer is filtered. At the end of filtration, the filter is washed three or four times with hot distilled water and dried in a thermostat, then a layer of gasoline lubricant solution is filtered through the same filter.

5. PACKAGING, LABELING, TRANSPORT AND STORAGE

Lubricant tubes are packed in wooden or plywood boxes in rows, between the rows there should be cardboard or paper spacers.

Gross and net weights are not indicated on tubes. The batch number, month and year of manufacture of the grease are stamped.

5.2. Grease must be stored in the manufacturer's container.

5.3. (Deleted, Rev. No. 3).

6. MANUFACTURER WARRANTY

6.1. The manufacturer guarantees the compliance of the grease with the requirements of this standard, subject to the conditions of transportation and storage.

6.2. The warranty period of storage in the manufacturer's packaging is five years from the date of manufacture.

(Revised edition, Rev. No. 1).

GOST 9433-80

Group B32

INTERSTATE STANDARD

LUBRICANT CIATIM-221

Specifications

Grease CIATIM-221. Specifications

OKP 02 5421 0800

Introduction date 1982-01-01

INTRODUCED BY Decree of the USSR State Committee for Standards dated May 19, 1980 N 2188
INSTEAD OF GOST 9433-60
Decree of the State Standard of the USSR dated April 17, 1991 N 513 removed the limitation of validity
EDITION with Amendments No. 1, 2, 3, approved in August 1982, April 1986, April 1991 (IUS 11-82, 7-86, 7-91)

This standard applies to grease intended for lubrication of friction units and mating surfaces "metal-metal" and "metal-rubber", operating at temperatures from minus 60 to plus 150 °C.
The requirements of this standard are mandatory.
(Changed edition, Rev. N 3).

1. TECHNICAL REQUIREMENTS

1.2. In terms of physical and chemical parameters, CIATIM-221 grease must comply with the requirements and standards specified in the table.


Name of indicator		Test method
1. Appearance	Homogeneous ointment, smooth structure from light yellow to light brown
2. Effective viscosity at minus 50 °C and an average strain rate gradient of 10 s, Pa s, not more than
3. Tensile strength at 50 °C, Pa, not less than
5. Penetration at 25 °C, 0.1 mm
6. Corrosive effect on metals	Withstands

1.1-1.2. (Changed edition, Rev. N 1, 3).

2. SAFETY REQUIREMENTS

2.1. CIATIM-221 lubricant is inactive, does not have a toxic effect on the body, does not irritate the skin and mucous membranes.
The maximum allowable concentration of the liquid lubricant base in the air of the working area is 10 mg/m.

2.2. When working with grease, it is necessary to use personal protective equipment in accordance with standard industry standards approved in the prescribed manner.

2.3. Persons working with lubrication should wash their hands with warm water and soap before eating, smoking and after finishing work.

2.4. The lubricant is not flammable and non-explosive, it is a combustible product of group IV. The flash point of the liquid lubricant base is above 265 °C.

When the lubricant catches fire, the following fire extinguishing agents are used: compositions SI-VK, SI-2 and SZHB-BF-2.

3. ACCEPTANCE RULES

3.1. Grease is accepted in batches.
A batch is considered to be a quantity of grease weighing up to 1000 kg, homogeneous in terms of quality, accompanied by a quality document.
(Changed edition, Rev. N 1, 2.).

3.4. The indicator "Evaporation at 150 ° C" is determined by the manufacturer at the request of the consumer.
(Changed edition, Rev. N 2).

4. TEST METHODS

4.1. Grease samples are taken according to GOST 2517-85.
The mass of the combined sample is 2 kg of lubricant.
In case of disagreement in assessing the quality of the lubricant, the sample should be stored for at least five years.

4.1-4.2. (Changed edition, Rev. N 1).

4.3. To determine the appearance, the lubricant is applied with a spatula on a glass plate measuring 50x70x2 mm along GOST 111-90 using a template (internal dimensions 35x35 mm, thickness 2 mm) and viewed with the naked eye in transmitted light.

4.4. The corrosion test is carried out on plates of copper grades M0k or M1k according to GOST 859-2001. Discoloration and slight reddish-brown staining of the plates is allowed.

4.5. When determining colloidal stability, the ashless filter is moistened with liquid 132-24 GOST 10957-74. The grease is pressed out at a load of (200 ± 10) g.

4.6. When determining the mass fraction of alkali, toluene of analytical grade is used as a lubricant solvent. By GOST 5789-78 and titrate the hot lubricant solution.
(Changed edition, Rev. N 2).

4.7. When determining mechanical impurities, a sample of lubricant is thoroughly mixed until a homogeneous mass is obtained with 75 cm3 of gasoline. The mixture is transferred to a separating funnel, 75 ml of 50% acetic acid are added GOST 61-75 and vigorously mix until the complete decomposition of the lubricant. After settling and separation of the layers, the lower acetic acid layer is filtered. At the end of filtration, the filter is washed three or four times with hot distilled water and dried in a thermostat, then a layer of gasoline lubricant solution is filtered through the same filter.

5. PACKAGING, LABELING, TRANSPORT AND STORAGE

5.1. Packing, marking, transportation and storage of lubricant - according to GOST 1510-84 with the following addition: the grease is packaged in tinplate cans and, at the request of consumers, in uncoated aluminum tubes or with an internal coating of BF-2 phenol-polyvinyl acetate adhesive according to GOST 12172-74 with a capacity of 40-200 g.
Lubricant tubes are packed in wooden or plywood boxes in rows, between the rows there should be cardboard or paper spacers.
Gross and net weights are not indicated on tubes. The batch number, month and year of manufacture of the grease are stamped.

5.2. Grease must be stored in the manufacturer's container.

5.3. (Deleted, Rev. N 3).

6. MANUFACTURER WARRANTY

6.1. The manufacturer guarantees the compliance of the grease with the requirements of this standard, subject to the conditions of transportation and storage.

6.2. The warranty period of storage in the manufacturer's packaging is five years from the date of manufacture.
(Changed edition, Rev. N 1).

The text of the document is verified by:
official publication
Oil products. Lubricants. Additives.
Specifications: Sat. GOSTs. -
Moscow: IPK Standards Publishing House, 2002

Ciatim-221 grease reduces wear and sliding friction of mating parts, is recommended for use in units where it is impossible to determine the degree of wear of working surfaces, as well as for lubricating moving elements of rocker/ball/roller mechanisms. It is a promising heat-resistant material based on silicone oil, which remains stable even when boiled. Reliably protects friction units and mating surfaces, it is used when it is impossible to use oils, when it is difficult to replenish and when it is necessary to seal stuffing boxes, taps and threaded connections. Stable demand for this product is due to an affordable price and practical packaging. The name CIATIM grease received from the abbreviated name of the lubricant developer organization - Central Institute Aviation Fuels And Oils.

Composition and low temperature properties

The purpose of the lubricant Ciatim 221 is determined by its physico-chemical properties. Of the main features it should be noted:

appearance at ordinary temperature - soft, ointment-like, non-flowing material;
family - calcium lubricants;
texture - homogeneous, smooth, reminiscent of vaseline;
color - white, yellowish, light shades of gray or brown;
base - organosilicon liquid "132-24" in the total volume up to 88%, please note that its replacement with other products is not allowed according to the technological regulations;
thickener - calcium soap or calcium stearate-acetate in a volume of up to 10%;
to improve the viscosity properties and adhesion, as well as to increase the thermal-oxidative stability, up to 5% of an antioxidant additive is additionally introduced;
the dropping point is above 200 degrees, and the evaporation rate is not more than 2% per hour at a temperature of 150 degrees;
colloidal stability is only 7%, which guarantees long-term storage without changing properties and the possibility of long-term operation in nodes without the need for replacement;
corrosion tests - withstands;
packaging - storage in leaky containers is prohibited due to hygroscopicity, tin cans are recommended, less often aluminum tubes;
a guarantee from the manufacturer in an original hermetically sealed container - five years from the date of issue, however, the lubricant retains its properties for up to 40 years;

Lubrication features that appear during operation:

insoluble in water, hygroscopic, remains stable at boiling point, but at high humidity it hardens and loses its original characteristics;
used as a multifunctional lubricant in difficult operating conditions that require resistance to washout, to low (up to -60C) and high (up to 150C) temperatures and their sudden changes;
with a short heating up to 180C, it does not lose functionality and does not harden;
the manufacturer focuses on the fact of incompatibility with other lubricants - even accidental mixing should be excluded, including products with lithium based on petroleum oils;
the special additives included in the composition increase the efficiency of work - friction units and metal-to-metal mating surfaces are protected from corrosion, scuffing and wear;
fire and explosion-proof, does not apply to self-igniting products;
inertness to polymers makes it possible to use the product for lubricating the surface of sealing rings of pneumatic cylinders, as well as for metal-rubber surfaces operating in vacuum;
refers to non-toxic products, safe for respiratory organs and skin, however, the manufacturer recommends using PPE when working;
colloidal stability - high, which helps to maintain the consistency of the lubricant;
chemically resistant - used to seal threads, valves, glands;
for friction pairs metal and metal rubber;
is able to ensure trouble-free operation of the nodes of most modern devices, incl. and devices with a rotation speed of up to 10 thousand revolutions per minute.

Scope of use

The product is a multifunctional grease that works with various loads, in a wide temperature range and at any speed. It finds application in many industries, including instrument-making, metallurgical, automotive, agricultural, aviation, petrochemical and other industrial sectors.

mating surfaces of metal-rubber working in high vacuum;
control and measuring and radio devices, as well as mechanisms with a rotation speed of up to 10,000 min-1;
drive mechanisms, as well as all types of gears;
lens mechanisms for photo and film equipment;
navigation systems, counting devices, automatic control and devices with a frequency of full revolutions up to 10 thousand per minute;
rolling bearings of electric machines of control and monitoring systems in lightly loaded gearboxes;
pneumatic brake boosters, steering racks and vehicle suspension;
many other elements - it is enough to check with the manufacturer or its official representative for compatibility.

Functional analogues

Among the products of Russian and foreign production, the following can be noted as analogues according to their functional purpose:

Mobil SHC - a slightly wider temperature range, hygroscopic in water, retains stability during oxidative reactions;
HUSKEY HVS-100 Silicone Grease and CIATIM-201 grease - protects aggregate bearings from oxidation, wear and scuffing aircraft nodes of friction pairs and screw pairs in the range of -60 / +120 degrees, the composition also does not contain mechanical impurities;
O-Grease - recommended for operation in the Far North, often serves as a single lubricant;
Mobiltemp - suitable for conservation and lubrication of outdoor apparatus, friction points and mating surfaces are reliably protected from moisture and corrosion, but leakage of the product is not excluded due to its low mechanical stability;
Aeroshell "Grease15" - protects aircraft bearings from friction units from the possibility of corrosion in the temperature range from - 73 to +232 degrees Celsius;
Unirex S2 - the upper limit of the operating temperature is 200C, and the dropping point is 280 degrees, it is resistant to oxidation and is characterized by anti-corrosion properties, suitable for lubricating electrical machines of control systems and instruments, but requires preliminary clarification of compatibility with rubber and polymer materials, as softening and loss of shape of the seals may occur.

CIATIM-221 grease is insoluble in water, hygroscopic, and remains stable even when boiled. this lubricant has found a field of application in electrical machines at temperatures from minus 60 to 150 degrees, in addition to electric motors and rubber-metal friction pairs. When moisture is absorbed, it becomes compacted and has low anti-wear characteristics. Before applying the lubricant, the assembly must be cleaned of previous materials. The anti-wear properties of the lubricant are quite high.

TsIATIM 221 high-temperature grease is used in a wide range of sign-variable operating environment temperatures from 60 to +150 degrees.

Application:

CIATIM 221 grease is most often used in the maintenance of bearing assemblies of electric motors, adjustment and control units, various devices, incl. and operated in vacuum conditions, at a pressure of 0.0066 atmospheres.

During preventive maintenance of drying chambers, computer technology, for lubrication of ball bearings in fans in high and low temperature operation.

The lubricant does not dissolve in aqueous solutions, has a high hygroscopicity and does not lose its working qualities even when exposed to steam and boiling water. When absorbing vapors or water, it condenses.

CIATIM 221 is inert to rubber polymers and plastics, does not cause their swelling and destruction, and has unique performance characteristics.

1. TECHNICAL REQUIREMENTS

2. SAFETY REQUIREMENTS

3. ACCEPTANCE RULES

4. TEST METHODS

5. PACKAGING, LABELING, TRANSPORT AND STORAGE

6. MANUFACTURER WARRANTY

CIATIM 221 characteristics and application

What is CIATIM 221F used for?

Which is better, Litol 24 or CIATIM 221?

CIATIM 201 and 221, what is the fundamental difference?

INTERSTATE

LUBRICANT TSIAGIM-221

Specifications

1. TECHNICAL REQUIREMENTS

2. SAFETY REQUIREMENTS

3. ACCEPTANCE RULES

4. TEST METHODS

4.1-4.2. (Revised edition, Rev. No. 1).

GOST 9433-80 S. 3

5. PACKAGING, LABELING, TRANSPORT AND STORAGE

5.3. (Deleted, Rev. No. 3).

6. MANUFACTURER WARRANTY

1. TECHNICAL REQUIREMENTS

2. SAFETY REQUIREMENTS

3. ACCEPTANCE RULES

4. TEST METHODS

5. PACKAGING, LABELING, TRANSPORT AND STORAGE

6. MANUFACTURER WARRANTY

Composition and low temperature properties

Lubrication features that appear during operation:

Scope of use

Functional analogues

Perhaps you will be interested